Bedienungsanleitung Stiebel Eltron DHB-E 18 SLi electronic (Seite 7 von 20) (Englisch)

650329

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

 





Pipe set, offset installation

This pipe set with pipe bends is required if you want to have the

appliance vertically offset against the water connection by approx.

90 mm downwards.

Pipe set for replacing a gas water heater

This pipe set is required if the installation has existing gas water

heater connections (cold water connection on the left and DHW

connection on the right).

DHB replacement pipe set

2 water couplings. These allow the appliance to be connected to

the available water plug-in connections of a DHB.

Load shedding relay LR 1-A

The load shedding relay for installation in the electric distribution

board enables priority control of the instantaneous water heater

when electric storage heaters are being operated simultaneously,

for example.

ZTA 3/4 – Central thermostatic valve

Thermostatic valve for centralised premixing, e.g. an instantaneous

water heater in conjunction with a solar thermal system.

9. Installation

9.1 Installation information

9.1.1 Flow pressure

If the ﬂow rate required for the appliance to switch on is not

achieved even with the tap fully open, remove the ﬂow limiter.

Replace it with the plastic proﬁle washer supplied. If required the

pressure in the water installation can also be raised.

Note

For the thermostatic valve to function correctly, the ﬂow

limiter for this valve must not be replaced with the plastic

proﬁle washer.

26�02�02�0820

1 Flow limiter

2 Plastic proﬁle washer

9.1.2 Flexible water connection lines

If the appliance is connected with ﬂexible water connection lines,

ensure that the bayonet ﬁttings of the pipe bends do not become

twisted inside the appliance.

9.1.3 Appliance with changeover connected load

The appliance DHB-E 18/21/24 SLi is set to 21kW when delivered.

If the appliance is installed with a different output, take the

following steps:

 Re-plug the coding card according to the selected output; for

selectable output and fuse protection of the appliance see

"Speciﬁcation“.

 Mark the selected output on the type plate using a

permanent marker.

 Install the ﬂow limiter with a rating corresponding to that of

the appliance. The colour of the ﬂow limiter is given in the

table "Speciﬁcation".

26�02�02�0822

10. Installation

10.1 Installation location

The appliance is exclusively designed for installation on a solid

wall. Ensure that the wall has a sufﬁcient load-bearing capacity.

Always install the appliance vertically (over or undersink) in a

room free from the risk of frost.

10.1.1 Undersink

26�02�02�0807

1 Cold water inlet

2 DHW outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron DHB-E 18 SLi electronic Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stiebel Eltron DHB-E 18 SLi electronic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info