Bedienungsanleitung Stiebel Eltron DHB-E 24 SLi electronic (Seite 12 von 20) (Englisch)

650331

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

 





26�02�02�0821

1 Knock-out

2 Cap guides

3 Back panel guides

10.3.8 Installing lower part of back panel

If using threaded connections for ﬁnished walls, the lower part of

the back panel can also be installed after ﬁtting the taps/valves.

To do this, carry out the following steps:

 Cut open the lower part of the back panel.

 Fit the lower part of the back panel by bending it out at the

sides and guiding it over the pipes.

 Insert the connection pieces from behind into the lower part

of the back panel.

 Click the lower part of the back panel into place.

 Secure the lower part of the back panel with a screw.

26�02�02�1080

1 Lower part of back panel

2 Connection piece from the pack

3 Screw

10.3.9 Installation in case of appliance replacement

An existing mounting bracket can be used when replacing Stiebel

Eltron appliances (except "DHF"). For this, open a suitable knock-

out in the back panel for the stud of the existing mounting bracket.

If the appliance is being installed in place of a DHF, move the

stud on the mounting bracket as shown in the diagram "Mounting

bracket for DHF appliance replacement". The stud cuts its own

groove. Then turn the mounting bracket through 180° to be

mounted on the wall. The logo "DHF" is then turned towards the

reader.

If replacing a third party appliance, suitable holes for rawl plugs

can be used.

26�02�02�0815

10.3.10 Undersink installation with turned appliance cap

The appliance cap can be positioned on the back panel turned

through 180°. This particularly advantageous for undersink

installation. For this take the following steps:

 Remove the user interface from the appliance cap by

pressing the locking hooks.

 Turn the appliance cap and click the user interface into place,

ensuring that all locking hooks click into place. To install the

user interface more easily, press against the inner side of the

appliance cap (in the shaded area, see diagram "Appliance

cap for undersink installation").

Material damage

Never install a user interface with a faulty locking

hook. Otherwise the safety of the appliance cannot be

guaranteed.

 Plug the set value transducer cable into the "set temperature"

PCB; see "Commissioning".

 Hook the appliance cap in at the bottom and pivot it up onto

the back panel. Ensure the all-round seal of the back panel

sits tightly by pushing the cap gently forwards and back.

 Close the appliance with the screw in the cap.

26�02�02�0817

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron DHB-E 24 SLi electronic Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stiebel Eltron DHB-E 24 SLi electronic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info