Bedienungsanleitung Stiebel Eltron DHE 18 SLi (Seite 33 von 124) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

650335

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

www.stiebel-eltron.com DHE SLi | 33

INSTALLATION

Installation

Connecting a load shedding relay

Install the load shedding relay in the distribution board in conjunc-

tion with other electric appliances, e.g. electric storage heaters.

The relay responds when the instantaneous water heater starts.

The load shedding relay is available as an accessory.

Material damage

Connect the phase that switches the load shedding relay

to the indicated terminal of the mains terminal in the

appliance (see chapter "Speciﬁcation / Wiring diagram").

Water installation for ﬁnished walls

Suitable pressure-tested taps can be ordered as accessories.

D0000033104

1 Water plug

2 Pressure tap for ﬁnished walls

 Fit the water plugs with gaskets to seal the connection below

the plaster. With pressure taps listed in the accessories, the

plugs and gaskets are part of the standard delivery.

 Install the tap.

 Place the lower part of the back panel under the connection

pipes of the tap and push the lower part of the back panel

into place.

 Secure the connection pipes to the appliance.

Water installation for ﬁnished walls with solder/ compression

ﬁtting

You can connect copper or plastic pipes with solder ﬁtting or

compression ﬁtting accessories.

The solder ﬁtting with threaded ﬁtting is suitable for 12mm cop-

per pipes.

 Push the union nuts over the connection pipes.

 Solder the inserts to the copper pipes.

 Push the lower part of the back panel under the connection

pipes of the tap and click the lower part of the back panel

into place.

 Secure the connection pipes to the appliance.

Note

Observe the tap manufacturer's instructions.

Water installation for ﬁnished walls, ﬁtting the appliance cover

D0000041391

1 Back panel guides

2 Screw

3 Cover guides

4 Knock-out

 Cleanly break out the knock-outs in the appliance cover. If

necessary, use a ﬁle.

Note

If the tap connection pipes are slightly offset, the appli-

ance can be sealed using the tabs on the cover guides.

 If the tap connection pipes are offset, do not ﬁt any

back panel guides.

 If installing tap connection pipes which are not offset, break

off the tabs on the cover guides.

 Click the cover guides into place in the knock-outs.

 Position the back panel guides on the pipes and push them

together. Then push the guides until they are resting against

the back panel.

 Secure the back panel at the bottom with a screw.

Installation of lower part of back panel with threaded ﬁtting

for ﬁnished walls

You can install the lower part of the back panel after ﬁtting the

taps.

26�02�02�1080

1 Screw

2 Connection pieces from the pack

 Cut open the lower part of the back panel at the markings.

 Fit the lower part of the back panel by bending it out at the

sides and guiding it over the pipes.

 Insert the connection pieces from behind into the lower part

of the back panel.

 Click the lower part of the back panel into place.

 Secure the lower part of the back panel with a screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiebel Eltron DHE 18 SLi Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info