Bedienungsanleitung Stiga 107M HD (Seite 7 von 11) (Englisch)

608620

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

3.2 Installation of 107 M HD, 121 M

1. Place the cutting deck in position in front of the

machine.

2. Install the following components on both wheel

axles:

• Washer (3:B).

• Deck mount (3:C).

• Washer (3:B).

• Circlip (3:A).

3. Remove the pins on both sides. See fig. 7:I and

fig. 13.

4. Screw the arms into each other. See fig. 4.

5. Suspend the cutting deck in the implement lift-

er. See fig. 14.

6. If the deck has electrical cutting height adjust-

ment, connect the cable to the machine’s front

right socket. See fig. 15.

3.2.1 Belt, 107 M HD, 121 M

The cutting deck’s rear section should rest on the

floor (it should not be lifted or secured).

Install the belt as follows:

1. 107 M HD

: Set the maximum cutting height.

121 M

: Set the cutting height in the centre posi-

tion

2. Remove the belt cover. See fig. 8 and 10. The

number in the figure indicates the key width.

3. Locate the belt around the machine’s belt pulley

(16:M).

4. Force the belt onto the cutting deck’s belt pul-

ley.

5. Grip the belt tensioner’s lever with your left

hand. Pull the lever and apply the tensioner to

the outside of the belt with your right hand. See

fig. 16.

6. Fit the belt cover. See fig. 8 and 10.

7. Lift up and secure the rear section of the cutting

deck.

107 M HD on machines with 17” wheels:

Install

the pins in the third hole from the top. See fig.

13.

107 M HD on machines with 16” wheels:

Install

the pins in the fourth hole from the top. See fig.

13.

121 M: Lift up and install the pins (7:I).

3.3 Installing 107 M

1. Place the cutting deck in position in front of the

machine.

2. Install the following components on both wheel

axles:

• Washer (11:B).

• Deck arm (11:D).

• Washer (11:B).

• Circlip (11:A).

3. Install the deck arms in the cutting deck’s front

corners. After tightening, it should be possible

to move the rear section of the cutting deck free-

ly up and down.

4. Suspend the cutting deck in the implement lift-

er. See fig. 14.

3.3.1 Belt, 107 M

The cutting deck’s rear section should rest on the

floor (it should not be lifted or secured).

Install the belt as follows:

1. Set the maximum cutting height.

2. Remove the belt cover. See fig. 10. The number

in the figure indicates the key width.

3. Locate the belt around the machine’s belt pulley

(16:M).

4. Force the belt onto the cutting deck’s belt pul-

ley.

5. Grip the belt tensioner’s lever with your left

hand. Pull the lever and apply the tensioner to

the outside of the belt with your right hand. See

fig. 16.

6. Fit the belt cover. See fig. 10.

7. Lift up the cutting deck so that it locks in the

catches (12:L).

3.4 Tyre pressure

Adjust the air pressure in the tyres as follows:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

3.5 Basic setting

In order for the cutting deck to cut optimally, the

correct basic setting is required. The deck is in the

basic setting when its rear edge is 5 mm above its

front edge. This means that the deck is inclined

forwards.

Carry out basic setting as described below.

3.5.1 Basic setting, 125 Combi Pro, 107 M

The deck is in the basic setting when the actions

under 3.1.1 and 3.2.1 have been carried out.

3.5.2 Basic setting, 107 M, 121 M

See fig. 17 and perform basic setting of 107 M and

121 M as follows:

1. Place the machine on a level floor.

Requirements for floor flatness: ±1 mm/m. No

slope towards a floor drain or similar may occur

in front of or behind the machine.

2. The tyres must have the correct air pressure.

See 3.4.

3. Place the deck in transport position and lay a

plane-parallel plank under the deck.

4. Place a 5 mm tall spacer on the plank under the

rear edge of the cutting deck, and lower the

deck to the working position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga 107M HD Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info