Bedienungsanleitung Stiga 110 S (Seite 4 von 5) (Englisch)

608618

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

ENGLISH

MOWING HINTS

For the best effect follow this advice:

- mow regularly

- use full throttle on the engine.

- keep the underside of the mower deck clean.

- use sharp blades.

- do not mow wet grass.

MAINTENANCE

No service work to the engine or mower

deck is to be carried out unless the fol-

lowing action has been taken:

- the engine has been stopped.

- the ignition key has been removed.

- the ignition cable has been removed

from the spark plug.

- the parking brake is engaged.

- the mower deck has been disengaged.

CLEANING

Rinse off the underside of the mower deck casing

with a garden hose after using the mower.

If grass has dried onto the casing dismantle the

mower deck and scrape the underside clean.

If necessary, to improve the underside it can be

painted to prevent rust.

Do not spray with high pressure water

against the bearing housings on top of

the mower deck when the transmission

cover is removed. Otherwise water may

penetrate the bearings.

LUBRICATION

The attachment's support wheels are fitted with

two grease nipples J (fig 1). Lubricate using a uni-

versal grease periodically during the season.

Grease other moving parts too.

REPLACEMENT OF DRIVE BELT

CENTRAL BELT PULLEY - MOWER

DECK

1. Unhook the tension roller spring H.

2. Remove the mower deck from the machine.

3. Unscrew the screws K and remove the transmis-

sioncasing(fig4).

4. Slide in the unit towards the machine and pull

off the v-belt from the central belt pulley.

5. Change the damaged v-belt. Always use an orig-

inal v-belt. The tension roller G should rest to the

left of the v-belt as seen from the driver's seat

(fig 3).

6. Fit the screws K (fig 4).

7. Fit the mower deck in the machine's attachment

brackets.

8a. Park -1999:

Hook the tension roller spring H into the floor on

the right-hand side (fig 3).

8b. Park 2000-

Hook the tension roller spring H into the fastener,

just behind the front right wheel (fig 3).

REPLACEMENT OF THE DRIVE

BELT IN THE MOWER DECK

1. Remove the screws K and remove the transmis-

sion casing (fig 4).

2. Loosen the spring which holds the tension roller.

3. Change the v-belt and replace in the reverse or-

der. Always use original v-belts.

BLADES

Use protective gloves to prevent cuts

when changing blades/blade tips.

Make sure the blades are always sharp. This gives

the best cutting results.

SHARPENING

For safety reasons the blades must not be sharp-

ened on an emery wheel. Incorrect sharpening ( =

high temperature) can result in the blades becom-

ing brittle.

When the blades are due to be sharpened, the wet

grinding method with a waterstone or grindstone is

to be used.

Following sharpening, the blades must

be balanced to avoid vibration damage.

CHANGING BLADES

Always use original spare parts when changing the

blades, blade attachments or bolts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga 110 S Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info