Bedienungsanleitung Stiga B 28 D (Seite 111 von 408) (Alle Sprachen)

608716

111

Zoom out

Zoom in

Vorherige Seite

1/408

Nächste Seite

USE OF THE ENGINE (Fig. 8)

Cutting device speed is regulated by the throttle

trigger (2), located on the rear handgrip (4) or the

right handgrip (4a) of the handlebar.

The throttle trigger only works if the lockout (3) is

pressed at the same time.

The movement is transmitted from the engine to

the drive shaft by a centrifugal mass clutch that

prevents the shaft from moving when the engine

is running at minimum speed.

WARNING!

Do not use the machine if

the cutting device moves when the engine is

running idle; in this case, contact you dealer.

The correct running speed will be achieved by

pressing the throttle trigger (2) as far as possible.

IMPORTANT

Avoid using the engine at full

power for the rst 68 working hours.

STOPPING THE ENGINE (Fig. 8)

To stop the engine:

– Release the throttle trigger (2) and allow the

engine to run idle for a few seconds.

– Set the switch (1) to «STOP».

WARNING!

When you have reduced

speed to a minimum, it will take a few seconds

for the cutting device to stop

3. Press the primer device button (6) 3 or 4 ti mes

to prime the carburettor.

4. Hold the machine rmly on the ground with one

hand on the power unit, in order not to lose

control of the machine during startup (Fig. 9).

IMPORTANT

To prevent distortions, the

drive tube must not be used as a support for the

hand or knee during startup.

5. Pull the starter rope slowly for 10 - 15 cm until

you feel some resistance, then tug it hard a few

times until you hear the engine turn over.

IMPORTANT

To avoid breaking the sta r ter

rope, do not pull the whole length of it or let it slide

along the edge of the cable guide hole. Release

the starter gradually, to avoid letting it y back un-

controllably.

6. Pull the starter rope again until the engine starts

as normal.

WARNING!

Starting the engine with

the choke engaged causes the cutting device

to move, only stopping when the choke is di-

sconnected.

7. When the engine is started, disconnect the

starter by turning the lever (2) to «RUN».

8. Briey activate the throttle (2) to bring the

engine down to minimum, with the switch (1)

which will move automatically to the «RUN»

position.

9. Let the engine run idle for at least 1 minute

before using the machine.

IMPORTANT

If the starter rope is pulled

repeatedly with the choke on, it may ood the en-

gine and make starting dicult.

If you have ooded the engine, remove the spark

plug and gently pull the handle on the starter rope

to eliminate any excess fuel; then dry the spark

plug electrodes and replace it on the en gine.

• Hot starting

When hot starting (immediately after stopping the

engine):

– Set the switch (1) to position «RUN», then follow

points 4 - 5 - 6 – 9 in the previous procedure.

HOW TO START - USE - STOP THE ENGINE 109

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga B 28 D Seite 111

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info