Bedienungsanleitung Stiga B 33 (Seite 113 von 408) (Alle Sprachen)

608718

113

Zoom out

Zoom in

Vorherige Seite

1/408

Nächste Seite

keeping the cutting device at a distance from the

operator.

• Cutting near fences/foundations (Fig. 14)

Slowly approach the cutting line head to fences,

posts, rocks, walls, etc. without hitting them hard.

If the line strikes a solid object it could break or be-

come worn; if it gets tangled in a fence it could break

abruptly.

In any case, cutting around pavements, foundations,

walls, etc. can cause greater wear than normal in

the line.

• Cutting round trees (Fig. 15)

Walk round the tree from left to right, approaching

the trunks slowly so as not to strike the tree with the

line and keeping the cutting line head tilted forward

slightly.

Remember that the nylon line could lop or damage

small shrubs and that the impact of the nylon line

against the trunk of bushes or trees with soft bark

could seriously damage the plant.

• Adjusting line length when working (Fig. 16)

This machine is tted with a “Tap & Go” head.

To release more line, tap the cutting line head against

the round with the engine at top speed: the line will

be released automatically and the knife cut o the

excess length.

END OF OPERATIONS

When you have nished your work:

– Switch o the engine as indicated above (Chap. 6).

– Wait for the cutting device to stop and t the blade

guard.

WORKING TECHNIQUES

a) 3-point blade (Fig. 11)

Start cutting above the undergrowth and then move

down with the scything blade so as to cut the brush

into small pieces.

b) 4-point blade (Fig. 12)

Proceed using the machine as a traditionalscythe,

with a circular movement of about 60-90°, thus mov

ing outside the undergrowth, andso on.

c) Cutting line head

WARNING!

Use ONLY nylon lines. The

use of metal lines, plasticised metal lines and/or

lines not suitable for the head can cause serious

injuries and wounds.

During use it is advisable to stop the engine peri

odically and remove the weeds wound round the ma-

chine, so as to prevent the drive tube from overheat-

ing due to the grass caught under the guard.

Remove the caught-up grass with a screwdriver to

allow the rod to be properly cooled.

WARNING!

Do not use the machine for

sweeping, tilting the cutting line head. The po

wer of the engine could throw objects and small

stones 15 metres or more, causing damage and

injuries to people.

• Cutting in motion (Scything) (Fig. 13)

Proceed at a regular pace, with a circular motion

similar to a traditional scythe, without tilting the cut-

ting line head during the operation.

First try cutting at the right height in a small area, so

as to then achieve a uniform cutting height keeping

the cutting line head at a constant distance from the

ground.

For heavier cutting it can be useful to tilt the cutting

line head by about 30°.

WARNING!

Do not work in this way if

there is the possibility of causing objects to be

thrown, which could harm people and animals

and cause damage.

• Precision cutting (Trimming)

Keep the machine slightly tilted so that the lower part

of the cutting line head does not touch the ground

and the cutting line is at the required point, always

USING THE MACHINE 111

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga B 33 Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info