Bedienungsanleitung Stiga COMPACT HST (Seite 8 von 15) (Englisch)

608675

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

ENGLISH

2.4.7 Ignition lock (1:E)

Do not leave the machine with the key

in position 2 or 3. There is a fire risk,

fuel can run into the engine through the

carburettor, and there is a risk of the

battery being discharged and damaged.

Ignition lock used for starting/stopping the engine.

Four positions:

1. Stop position – the engine is short-

circuited. The key can be removed.

2/3. Operating position.

4. Start position – the electric start motor

is activated when the key is turned to the

spring-loaded start position. Once the eng-

ine has started, let the key return to opera-

ting position 2/3.

2.4.8 Gear lever (2:H) (Man))

A lever for selecting one of the five forward gears

in the gearbox (1-2-3-4-5), neutral (N) or reverse

(R).

The clutch pedal must be kept pressed in when

changing gear.

NOTE! You must make sure the machine is quite

stationary before changing from reverse to forward

gear or vice versa. If a gear does not engage

immediately, release the clutch pedal and then

press it in once again. Engage the gear once again.

Never force a gear in.

2.4.9 Power take-off (2:G)

A lever for engaging and disengaging the power

take-off for operating front-mounted accessories.

Two positions:

1. Lever in forward position – power take-

off disengaged.

2. Lever in backward position - power

take-off engaged.

2.4.10Clutch release lever (HST, 4WD)

A lever for disengaging the variable transmission.

HST is equipped with a lever, connected to the rear

axle. See (5:N).

4WD is equipped with two levers, connected to the

rear axle (6:O) and the front axle (6:P).

The disengagement lever must never be

between the outer and inner positions.

This overheats and damages the trans-

mission.

The levers enable the machine to be moved by

hand without the help of the engine. Two positions:

1. Lever in the inner position –

transmission engaged for normal

operation.

2. Lever in the outer position –

transmission disengaged. The

machine can be moved by hand.

The machine may not be towed over long distances

or at high speeds. The transmission could be dam-

aged.

The machine must not be operated with

the forward most lever in the outer po-

sition. Risk of damage and oil leakage in

the front axle.

2.4.11 Seat (3:I)

The seat can be folded and is adjustable

front-rear. The seat is locked in the folded

up position using the catch (3:K) and ad-

justed front-rear using the knobs (3:J).

The seat is equipped with a safety switch that is

connected to the machine’s safety system. This

means that certain dangerous activities are not pos-

sible when there is nobody in the seat.

2.4.12 Engine casing (4:L)

To access the fuel cock, battery and engine

the engine is equipped with engine casing

that can be opened. The engine casing is

locked by a rubber strap.

The engine casing is opened as follows:

1. Detach the rubber strap (4:M) at the front edge

of the engine casing.

2. Carefully lift the engine casing back.

Close in reverse order.

The machine may not be operated un-

less the engine casing is folded down

and locked. Risk of burns and crushing

injuries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga COMPACT HST Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info