Bedienungsanleitung Stiga SILEX 87 B (Seite 21 von 128) (Alle Sprachen)

608769

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ATTENTION! The used oil must not be drained into the sewer system or waterworks. In order to prevent any pollution to the water-table. Most garages

have used oil deposits, or use the authorized deposits according to your local authority regulations.

TRANSMISSION SCYTHING BAR (Fig. 12) there are 2 greasing point (1-2) . Important : after every use of the motor mower , please clean

and grease the scything bar and all motion parts/mechanisms.

ENGINE SERVICING ( please read the specic part). The motor mower is delivered equipped with a 4 stroke engine , NO OIL is included. Please

ll the tank in up to the shown level ( capacity about 0,5 kg.). Referring to the oil/viscosity type, please follow the engine producer instructions.

SERVICE - GARAGING : the motor mower is undoubted one of the most used agricultural equipment and need a good and frequent servicing.

We recommend you to clean the machine very deeply after every use. Keep attention that all the nuts , screws and bolts are tightened in order to

guarantee a good machine working on safety conditions. Leave the machine to cool before garaging anyhow don’t room it if the tank contains still

contains some fuel as the vapours could reach some blazes or sparks. To lower the re danger , keep the engine , the silencer and the fuel area free

from leaves, grass or greasy substances.

If the machine is not used for long periods it is essential to protect the blade and the bar using some anticorrosive and antioxidant materials. The

presence of impurities or foreign bodies on the meadow, damages the teeth sharpening of the scything bar. It is useful to sharpen the blade and check

the teeth integrity every 4-6 hours of use. Only if you keep a good sharpening teeth level you can obtain the best grass cut.

BLADE SHARPENING (Fig. 13) : according to the frequency and the type of use , the cutting sections have to be sharpened about every

10 hours working. To obtain a perfect sharpening you need to use and electric sharpening machine (15.000/20.000 turns/minute) , grinding-headed

with a diameter 25 mm and length 35 mm. The blade has to be sharpened from the internal part of the rod to tip.end section using the head grinding.

The blade sections have to be sharpened in a 25° deg. angle.

DESCRIPTION (Fig. 15) 1) Start-Stop operating lever - 2) Drive operating lever - 3) Cutter bar clutching control lever - 4) Engine - 5) Cutter

bar. 6) Cable-guide Bracket – 7) Cowling.

TECHNICAL DETAILS Track: 430 mm - Length of cutter bar: 660/870 mm - Total length: 1350 mm - Total height: 1050 mm - Tires: 2 tires 4.00-6

- Mass: 49/52 kg. MOTOR - Cooling: air cooling - Fuel tank: 0,75 Litre. Please consult the relative instruction manual for other technical information

and details about the engine.

ACCESSORIES: front mount snow blade cm. 85 and pair chains. For the assembly of the snow blade , tighten the pin in the ttings connection

seating and x it using a “R” pin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga SILEX 87 B Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info