Bedienungsanleitung Stiga SRC 36 G (Seite 27 von 96) (Alle Sprachen)

608758

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

OPERATING INSTRUCTIONS

For the engine, read the relative instructions manual.

NOTE - The number which precedes each paragraph

links the references in the text to the respective illustra-

tions (listed on page 2 and following pages).

1. COMPLETE ASSEMBLY

NOTE - The machine can be supplied with some

parts already assembled.

WARNING - Unpacking and completing the assembly

should be done on a at and stable surface, with

enough space for moving the machine and its packa-

ging, always using suitable equipment.

Disposal of the packaging should be done in accor-

dance with the local regulations in force.

1.1

Assembling the handle bar

Connect the tie rod (1) to the two side elements of the

handle bar (2a) and (2b) and tighten the two nuts com-

pletely (3).

WARNING - The tie rod is an important safety ele-

ment so the above must be carried out correctly.

Unscrew the two nuts (4), then remove the two side

screws (5) and the head screw (6) from the support (7).

Fit the handle bar (2) on the support (7) making sure you

keep the cables under the support. Reposition the two

side screws (5) and the washers in the sequence indica-

ted, then tighten the two nuts (4) completely.

Run the jumper (8) against the support (7) and x it with

the screw (6).

1.2

Closure of the milling cutter axles

Fit the two caps (1) on the two ends of the milling cutter

axles (2).

1.3

Oil relling

• Drive

Lay the machine down on its right side.

Release the cotter pin (1), extract the pin (2) and remove

the milling cutters (3) and (4).

Unscrew the cap (5) and pour circa 120 cc of oil of the

same quality used for the engine in the hole.

Reassemble the cap (5) making sure to reposition the

gasket (6) and restore the milling cutters (3) and (4) with

relative pin(2) and cotter pin (1).

• Engine

Top up engine oil following the instructions given in the

relative manual.

1.4

Assembling the strut

Insert the strut (1) in its housing and x it at the desired

height using the pin (2) and cotter pin (3).

2. CONTROLS AND REGULATIONS

NOTE – The meanings of the symbols on controls are

explained on page 6 and following.

2.1

Throttle control

The throttle is controlled by the lever (1).

Lever positions are indicated on the relevant plate.

The throttle regulates milling cutter rotary speed and, at

the same time, the machine’s forward speed.

2.2

Milling cutter engagement lever

Milling cutter movement in contact with the ground moves

the machine forward.

To engage the cutters, press the safety lever (1) and pull

the engagement lever (2).

Release the lever (2), the milling cutters stop and the

machine stops moving forward.

2.3

Regulating hoeing depth

How deep milling cutters go into the ground can be re-

gulated using the strut (1) which can be positioned at 3

dierent heights.

The lowest position coincides with minimum hoeing

depth.

To change strut height (1), remove the cotter pin (3) and

the pin (2) and reposition it at the desired height.

2.4

Regulating the auxiliary wheel

The auxiliary wheel (1) can be positioned at two dierent

heights:

– lowered, in contact with the ground, to facilitate mo-

vement;

– raised, while working, to allow the milling cutters to cut

into the ground.

To shift from one position to another, grasp the wheel

(1), pull it till the pin comes out (2) from its housing in the

support (3) and reposition it at the desired height.

3. USING THE MACHINE

3.1

Starting the engine

For start up, follow the instructions in the engine manual,

then rmly pull the knob on the starter cable (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga SRC 36 G Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info