Bedienungsanleitung Stiga TORNADO 2098 (Seite 63 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

608469

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

4.3 KEY IGNITION SWITCH (Fig. 4.1 no.3)

«OFF» everything is switched o;

«HEADLIGHTS ON» (if tted);

«ON» activates all parts;

«START» engages the starter motor.

– On being released at the «START» position,

the key will automatically return to «ON».

– After turning the engine on, turn the lights on

(if tted) by turning the key to the «HEAD-

LIGHTS ON» position.

– To switch them o, turn the key to «ON».

4.4 PARKING BRAKE (Fig. 4.1 no.4)

This lever stops the machine from moving when

it has been parked. There are two positions:

«A» = Brake disengaged

«B» = Brake engaged

– The brake is applied by pressing the pedal

right down (4.21 or 4.31) and moving the lever

to position “B”. When you take your foot o

the pedal it will be blocked by the lever in the

lowered position.

– To disengage the parking brake, press the

pedal (4.21 or 4.31). The lever will return to

position «A».

4.5 CUTTING MEANS ENGAGE AND

BRAKE CONTROLS (Fig. 4.1 no.5)

The mushroom switch allows you to engage the

cutting means using the electromagnetic clutch:

«A» Pressed = Cutting means

disengaged

«B» Pulled = Cutting means engaged

– If you engage the cutting means without tak-

ing the necessary safety precautions, the

engine shuts down and cannot be restarted

(see 5.2).

– In disengaging the cutting means (Pos. «A»),

a brake is simultaneously activated which

stops their rotation within a few seconds.

4.6 CUTTING HEIGHT ADJUSTMENT

LEVER (Fig. 4.1 no.6)

There are seven positions for this lever, shown

as «1» to «7» on the label, which correspond to

various heights between 3 and 8 cm.

To go from one position to another, move the

lever sideways and put it back in one of the stop

notches.

4.7 REVERSE GEAR CUTTING CONSENT

BUTTON (Fig. 4.1 no.7)

By pressing and holding this button, it is pos-

sible to switch to reverse gear with the cutting

means engaged without causing the engine to

stop.

Mechanical transmission

4.21 CLUTCH / BRAKE PEDAL

(Fig. 4.2 no.21)

This pedal has two functions: during the rst

part of its travel it acts as a clutch, engaging

and disengaging drive to the wheels, and in

the second part it acts as a brake on the rear

wheels

IMPORTANT Do not keep the pedal half

way between clutch engagement or disen-

gagement, as this can cause overheating and

damage the transmission belt.

NOTE When the machine is in movement,

keep your foot off the pedal.

4.22 SPEED CHANGE LEVER

(Fig. 4.2 no.22)

This lever has seven positions for the 5 for-

ward speeds, the neutral position «N», and

reverse «R».

To go from one speed to another, press the

pedal (4.21) halfway and shift the lever as

shown on the label.

WARNING! Reverse must be en-

gaged when the machine has stopped.

Hydrostatic transmission

4.31 BRAKE PEDAL (Fig. 4.3 no.31)

This pedal works the brake on the rear

wheels.

4.32 CLUTCH PEDAL (Fig. 4.3 no.32)

This pedal engages drive in the wheels and

controls the machine’s forward and reverse

speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga TORNADO 2098 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info