Bedienungsanleitung Stiga TORNADO 2098 (Seite 66 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

608469

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

gressively increasing pressure on the pedal

and moving the accelerator.

WARNING! Drive must be engaged

as described below (see 4.32) to prevent

sudden engagement from causing tipping

up and loss of control of the vehicle, par-

ticularly on slopes.

5.4.3 Braking

First reduce the machine’s speed by reducing

the engine’s r.p.m., and then press the brake

pedal (see 4.21 or 4.31) to slow down the ma-

chine until it stops.

Hydrostatic transmission

The machine already slows down consider-

ably by just releasing the drive pedal.

5.4.4 Reverse

IMPORTANT Reverse must only be engaged

when the machine has stopped.

IMPORTANT To proceed in reverse gear with

the cutting means engaged, it is necessary to

press and hold the consent button (see 4.7) so

as not to cause the engine to stop.

Mechanical transmission

Press the pedal until the machine stops and

then switch into reverse by shifting the lever

sideways and into position «R» (see 4.22).

Gradually release the pedal to engage the

clutch and then begin moving in reverse.

Hydrostatic transmission

When the machine is stopped, start the re-

verse movement by pressing the drive pedal

in the «R» direction (see 4.32).

5.4.5 Grass cutting

Fig. 5.7) Adjust the position of the anti-chipping

wheels according to how irregular the ground is.

The anti-chipping wheels are used to reduce

the risk of tearing up sections of lawn, which can

occur when the edge of the cutting-means as-

sembly drags over irregular ground.

The four dierent heights of the wheels allow

you to maintain a safe distance between the cut-

ting means assembly and the ground.

To change the position, unscrew and remove

the screw (2) and reposition the wheel (1) with

the spacer (3) in the hole at the desired height;

then tighten the screw (2) onto the nut (4) as far

as possible.

WARNING! This should always be per-

formed on both wheels, positioning them at

the same height WITH THE ENGINE OFF AND

CUTTING MEANS DISENGAGED.

To start cutting:

– move the throttle to «FAST»;

– bring the cutting-means assembly to the high-

est position;

– engage the cutting means (see 4.5) only on

grass lawns; avoid engaging them on stony

ground or when the grass is very high;

– start moving forwards on the grass very

slowly and with utmost caution, as already

described;

– regulate the cutting height and speed (see

4.6) considering the conditions of the lawn

(the height, density and dampness of the

grass).

WARNING! When cutting on sloping

ground, the forward speed must be reduced

to ensure safe conditions (see 1A – C7-8-9).

Whatever the conditions, always reduce the

speed if you notice a drop in engine speed – if

you travel too fast compared to the amount of

grass being cut, you will not be able to mow the

grass well.

Disengage the cutting means and raise the

cutting-means assembly as high as possible

whenever you need to get past an obstacle

5.4.6 End of mowing

When you have nished mowing, disengage the

cutting means, reduce the engine speed and

ride the machine with the cutting-means assem-

bly in the highest position.

altezza.

5.4.7 End of work

Stop the machine, put the accelerator lever in

the «SLOW» position and turn o the engine by

putting the ignition key into the «OFF» position.

When the engine has stopped, close the fuel

stopcock (1) (if tted) (Fig. 5.8)

WARNING! To avoid backfire, put the

accelerator in the «SLOW» position for 20

seconds before stopping the engine.

IMPORTANT To keep the battery charged, do

not leave the ignition key in the «ON» or «HEAD-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga TORNADO 2098 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info