Bedienungsanleitung Stiga TURBO 53 4SE COMBI 2008 (Seite 19 von 72) (Alle Sprachen)

564025

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

STANDARDS OF USE

For instructions regarding the engine and the battery (if

supplied), read the relevant manuals.

NOTE – The machine can be supplied with some of the

components already fitted.

Remove the two lower knobs (1) and the screws (3)

from the side brackets of the handle.

Move the lower part of the pre-fitted handle (2) to its work-

ing position and fasten it with the lower knobs (1) and

screws (3) supplied, checking that the centring washers (4)

are positioned properly. Tighten the nuts (5).

Move the upper part (6) of the handle to its working posi-

tion and fasten it using the nuts and bolts (7) provided,

ensuring that the spiral (8) of the starter cable is positioned

correctly.

Attach the control cables using the strap (9) in the position

shown.

Attach the wiring sheath (if fitted) using the straps (10) in

the positions shown.

Insert the frame (1) in the sack (2) and attach the

plastic profiles (3) using a screwdriver, as shown in the

drawing.

With the plastic part (4) upside-down, fit the edge of the

cloth (5) right into the groove of the plastic part (4), starting

5–7 mm from the ends.

On models with an electric starter, connect the bat-

tery cable to the lawnmower’s general cable connection.

Untie the starter keys, fitted on the upper part of the han-

dle.

The throttle (where fitted) is controlled by the lever

(1) and positioned as shown on the relative plate. Some

models have a fixed speed, and therefore no need of a

throttle (2).

The blade brake is controlled by the lever (1), which

should be held against the handle when starting and using

the lawnmower.The engine stops when the lever is

released.

In power-driven models, draw the lever (1) towards

the handle for forward movement. The lawnmower stops

moving forward when the lever is released.

The height is adjusted using the special lever (1).

MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS

STOPPED.

Lift the stone-guard and attach the grass-catcher

(1) correctly as shown in the drawing.

To start the engine, follow the instructions in the

engine booklet and then pull the blade brake lever (1)

towards the handle and give a sharp pull on the starter

cable knob (2). For models with an electric starter, turn the

starter key (3).

3.2

3.1

3. GRASS CUTTING

2.4

2.3

2.2

2.1

2. DESCRIPTION OF CONTROLS

1.3

1.2

1.1

1. FINISH ASSEMBLY

The lawn will look better if it is always cut to the

same height and in alternate directions.

When you have finishing mowing, release the brake

lever (1) and disconnect the spark plug cap (2). Remove the

starter key (3) (where fitted). WAIT FOR THE BLADE TO

STOP before carrying out any type of work on the machine.

IMPORTANT – Regular, careful maintenance is essen-

tial for keeping the safety level and original perform-

ance of the machine unchanged in time.

Store the lawnmower in a dry place.

1) Wear strong working gloves during any cleaning, main-

tenance or adjustment operation on the machine.

2) Carefully clean the machines with water after each cut;

remove the grass debris and mud accumulated inside

the chassis to avoid their drying and thus making the

next start-up difficult.

3) The paintwork on the inside of the chassis may peel off

in time due to the abrasive action of the cut grass; in this

case, intervene promptly by touching up the paintwork

using a rustproof paint to prevent the formation of rust

that would lead to corrosion of the metal.

4) Should it be necessary to access the lower part, only tilt

the machine from the side shown in the engine hand-

book; following the relative instructions.

5) Do not drip petrol onto the plastic parts of the motor or

the machine to prevent damaging them and remove all

traces of spilt petrol immediately. The warranty does not

cover damage to plastic parts caused by petrol.

All operations on the blade should be carried out at

a specialized centre.

Note for specialized centres: Reassemble the blade (2) as

shown in the drawing and tighten the central screw (1)

using a torque wrench set to 35-40 Nm.

In power-driven models:

• adjust the tension of the belt with the nut (1) to get the

right measurement (6 mm).

• turn the adjusting nut (2) so that the wire (3) is slightly

loose and the lever (4) is idle.

To recharge a flat battery, connect to the battery

charger (1) following the instructions in the battery mainte-

nance handbook. Do not connect the battery charger

directly to the engine terminal. It is not possible to start the

engine using the battery charger as a power source, as it

may get damaged.

If the machine is to remain inactive for a long period, dis-

connect the battery leads after making sure that the battery

is fully charged.

Should you have any doubts or problems, do not hesitate

to contact your nearest Service Centre or your Dealer.

4.3

4.2

4.1

4. ROUTINE MAINTENANCE

3.4

3.3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stiga TURBO 53 4SE COMBI 2008 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info