667197
33
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
0458-719-9621-A
31
English
5 Preparing the Blower for Operation
correctly, components may no longer function properly or
safety devices may be rendered inoperative. This can
result in serious injuries.
Clean the blower and charging cable as described in
this instruction manual.
If the blower or charging cable are not serviced or repaired
correctly, components may no longer function properly or
safety devices may be rendered inoperative. This can
result in serious or fatal injuries.
Do not attempt to service or repair the blower or
charging cable.
If the blower or the charging cable require servicing or
repairs: Contact your STIHL servicing dealer.
5.1 Preparing the Blower for Operation
Perform the following steps before starting work:
Make sure the following components are in a safe
condition:
–Blower, @ 4.7.1.
Charging cable, @ 4.7.2.
Check the built-in battery, @ 10.2.
Fully charge the blower, @ 6.
Clean the blower, @ 15.1.
Mount the blower tube and nozzle, @ 7.
Check the controls, @ 10.
If 3 LEDs flash red while you are checking the controls:
Remove the activation key and contact your STIHL
servicing dealer.
Malfunction in blower.
If you cannot carry out this work: Do not use the blower
and contact your STIHL servicing dealer.
6.1 Charging the Blower
The charging time depends on several factors, e.g.
temperature of the blower or ambient temperature. The
actual charging time may differ from the specified charging
time. For specified charging times see www.stihl.com/
charging-times.
The charging process starts automatically
when the plug is inserted in a wall outlet and
the charging cable is connected to the
blower. The charging process stops
automatically when the blower is fully
charged.
The blower and charging cable heat up during the charging
process.
Remove the activation key.
Insert the plug (2) in a convenient wall outlet (1).
WARNING
Persons may trip over the connecting cable. This can result
in injuries and may damage the charging cable.
Lay the connecting cable flat on the floor.
Position the connecting cable (3).
5 Preparing the Blower for Operation
6 Charging the Blower, LEDs
4
3
2
1
0000-GXX-2274-A0
6
5
3
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stihl BGA 45 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info