Bedienungsanleitung Stihl FS 410 C K (Seite 6 von 48) (Englisch)

537262

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

FS 410 C, FS 410 C L

English

Transporting the Power Tool

Always stop the engine.

Carry the unit hanging from the shoulder

strap or properly balanced by the drive

tube.

To reduce the risk of cut injuries, fit

transport guard on the cutting

attachment, even when carrying the tool

for short distances – see also

"Transporting the Unit".

Transporting by vehicle: Properly secure

your power tool to prevent turnover, fuel

spillage and damage.

Fueling

Always shut off the engine before

refueling.

Do not fuel a hot engine – fuel may spill

and cause a fire.

Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly and avoid fuel spillage.

Fuel your power tool only in well-

ventilated areas. If you spill fuel, wipe

the machine immediately – if fuel gets on

your clothing, change immediately.

This reduces the risk of unit vibrations

causing the fuel cap to loosen or come

off and spill quantities of fuel.

To reduce the risk of serious or fatal

burn injuries, check for fuel leakage. If

fuel leakage is found, do not start or run

the engine until leak is fixed.

Before Starting

Check that your power tool is properly

assembled and in good condition – refer

to appropriate chapters in the instruction

manual.

– Check the fuel system for leaks,

paying special attention to visible

parts such as the tank cap, hose

connections and the manual fuel

pump (on machines so equipped). If

there are any leaks or damage, do

not start the engine – risk of fire.

Have your machine repaired by a

servicing dealer before using it

again.

– Use only an approved combination

of cutting attachment, deflector,

handle and harness. All parts must

be assembled properly and

securely.

– The stop switch must move freely.

– Check smooth action of choke

knob, throttle trigger lockout and

throttle trigger – the throttle trigger

must return automatically to the idle

position. The choke lever must

spring back from the g and <

positions to the run position F when

the throttle trigger lockout and

throttle trigger are squeezed.

– Check that the spark plug boot is

secure – a loose boot may cause

arcing that could ignite combustible

fumes and cause a fire.

– Check cutting tool or attachment for

correct and secure assembly and

good condition.

– Check protective devices (e.g.

deflector for cutting attachment,

rider plate) for damage or wear.

Always replace damaged parts. Do

not operate your machine with a

damaged deflector or worn rider

plate (lettering and arrows no longer

legible).

– Never attempt to modify the controls

or safety devices in any way.

To reduce the risk of seri

ous burn injuries, avoid

touching hot parts of the

machine, including the

gearbox housing.

Gasoline is an extremely

flammable fuel. Keep

clear of naked flames. Do

not spill any fuel – do not

smoke.

002BA479 KN

After fueling, tighten

down the fuel tank cap as

securely as possible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl FS 410 C K Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stihl FS 410 C K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info