Bedienungsanleitung Stihl HL94 (Seite 8 von 88) (Englisch, Spanisch)

667379

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

HL 94

English

WARNING

See also the "Fueling" chapter in your

Instruction Manual for additional

information.

Before Starting

WARNING

Always check your power tool for proper

condition and operation before starting,

particularly the throttle trigger, throttle

trigger lockout, throttle set wheel, stop

switch and cutting tool. The throttle

trigger must move freely and always

spring back to the idle position. Never

attempt to modify the controls or safety

devices.

WARNING

Check fuel system for leaks, especially

the visible parts, e.g., filler cap, hose

connections, manual fuel pump (only for

power tools equipped with a manual fuel

pump). Do not start the engine if there

are leaks or damage – risk of fire! Have

the machine repaired by a servicing

dealer before using it.

WARNING

Never operate your power tool if it is

damaged, improperly adjusted or

maintained, or not completely or

securely assembled.

WARNING

Check that the spark plug boot is

securely mounted on the spark plug – a

loose boot may cause arcing that could

ignite combustible fumes and cause a

fire.

Keep the handles clean and dry at all

times; it is particularly important to keep

them free of moisture, pitch, oil, grease

or resin in order for you to maintain a firm

grip and properly control your power

tool.

WARNING

The cutting tool must be properly

tightened and in safe operating

condition. Inspect for loose parts (nuts,

screws, etc.) and for cracked, bent,

warped or damaged blades. Regularly

check the condition and tightness of the

cutter blades – with the engine stopped!

Replace damaged cutter blades before

using the power tool. Always keep

blades sharp.

STIHL recommends that you always

spray the cutter blades with STIHL resin

solvent before starting work – with the

engine stopped! You can obtain this

protective spray from your dealer. Apply

generously.

Adjust carrying harness and hand grip to

suit your size before starting work.

Starting

On machines with an adjustable cutter

bar: Secure the cutter bar in the starting

position as described in the chapter

"Starting/Stopping the Engine." If this

starting position is not the desired

cutting position, you will then need to

carefully adjust the machine to the

desired position once the engine has

returned to idle and the blades are no

longer moving.

On machines with a defined transport

position (cutter bar folded against the

drive tube): Never start the machine in

the transport position, since the blades

are not engaged in that position and you

therefore cannot visually check to see

that they will be stopped at idle when

you start to adjust the cutter bar to the

desired cutting position (where the

blades are engaged).

Start the engine at least 10 feet (3 m)

from the fueling spot, outdoors only.

Unit vibrations can cause

an improperly tightened

fuel filler cap to loosen or

come off and spill quanti-

ties of fuel. In order to

reduce the risk of fuel

spillage and fire, tighten

the fuel filler cap by hand

as securely as possible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl HL94 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stihl HL94

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info