Bedienungsanleitung Stihl HS 81 R (Seite 11 von 70) (Englisch, Spanisch)

479259

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

English / USA

HS 81 R, HS 81 T

Take particular care when cutting

hedges next to or against wire fences.

Do not touch the wire with the cutting

blades. When working close to the

ground, make sure that no sand, grit or

stones get between the cutter blades.

Striking solid foreign objects such as

stones, fence wire or metal could

damage the cutting attachment and may

cause blades to crack, chip or break.

STIHL does not recommend the use of

your power tool when cutting in areas

where the blades could contact such

objects.

!Warning

Observe the cutting blades at all times –

do not cut any areas of the hedge that

you cannot see. When cutting the top of

a taller hedge, check the other side of

the hedge frequently for bystanders,

animals and obstructions.

Danger!

Your power tool is not

insulated against electric

shock. To reduce the risk

of electrocution, never

operate this power tool in the vicinity of

any wires or cables (power, etc.) which

may be carrying electric current.

!Warning!

If the cutting tool becomes clogged or

stuck, always turn off the engine and

make sure the cutting tool has stopped

before cleaning. Grass, weeds, etc.

should be cleaned off the cutting tool at

regular intervals.

Check the cutting blades at regular short

intervals during operation, or

immediately if there is a noticeable

change in cutting behavior:

– Shut off the engine.

– Wait until the cutting blades have

come to a complete standstill.

– Check condition and tightness, look

for cracks.

– Check sharpness

– Replace damaged or dull cutting

tools immediately, even if they have

only superficial cracks.

!Warning

The gearbox becomes hot during

operation. To reduce the risk of burn

injury, do not touch the gear housing

when it is hot.

!Warning!

The muffler and other parts of the engine

(e.g. fins of the cylinder, spark plug)

become hot during operation and remain

hot for a while after stopping the engine.

To reduce risk of burns do not touch the

muffler and other parts while they are

hot.

!Warning!

To reduce the risk of fire and burn injury,

keep the area around the muffler clean.

Remove excess lubricant and all debris

such as pine needles, branches or

leaves. Let the engine cool down sitting

on concrete, metal, bare ground or solid

wood (e.g. the trunk of a felled tree)

away from any combustible substances.

!Warning!

Never modify your muffler. The muffler

could be damaged and cause an

increase in heat radiation or sparks,

thereby increasing the risk of fire and

burn injury. You may also permanently

damage the engine. Have your muffler

serviced and repaired by your STIHL

servicing dealer only.

After Finishing Work

Always clean dust and dirt off the

machine – do not use any grease

solvents for this purpose.

Spray the blades with STIHL resin

solvent. Start and run the engine briefly

so that the solvent is evenly distributed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl HS 81 R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stihl HS 81 R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info