Bedienungsanleitung Stihl HSE 52 (Seite 26 von 272) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

537314

Zoom out

Zoom in

Vorherige Seite

1/272

Nächste Seite

HSE 42, HSE 52

English

– Cutting blades securely mounted

and in good condition (clean, move

freely, not warped), properly

sharpened and thoroughly sprayed

with STIHL resin solvent (lubricant).

– Check cutter guard (if fitted) for

damage.

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the power tool.

To reduce the risk of accidents and

personal injury, do not operate the unit if

it is not properly assembled and in good

condition.

To reduce the risk of electric shock:

– Always connect the power tool to a

properly installed wall outlet.

– Make sure the extension cord used

complies with the regulations for the

intended application.

– Check that the insulation of the

power cord, extension cord, plug

and coupling is in good condition.

Holding and Controlling the Power Tool

Always hold the unit firmly with both

hands on the handles. Wrap fingers and

thumbs firmly around the handles.

Right-handers

Right hand on the control handle and left

hand on the loop handle.

Left-handers

Left hand on the control handle and right

hand on the loop handle.

Make sure you have firm and secure

footing and hold the unit so that the

cutting blades are always away from

your body.

During Operation

In case of imminent danger or in an

emergency, switch off the motor

immediately – release the trigger switch

and switch lever.

Check that there are no bystanders in

the general work area.

Watch the cutting blades at all times – do

not cut areas of the hedge that you

cannot see.

Be extremely careful when cutting tall

hedges, check the other side of the

hedge before starting work.

Do not leave the machine outdoors in

the rain.

Your power tool is equipped with a

system designed to quickly stop the

cutting blades – they come to an

immediate standstill as soon as you

release the trigger switch or the switch

lever.

Check this function at regular short

intervals. To reduce the risk of injury, do

not operate your power tool if the cutting

blades continue to run after switch-off.

Contact your servicing dealer.

Take special care in slippery conditions,

on slopes or uneven ground.

Clear away fallen branches, scrub and

cuttings.

Watch out for obstacles: Roots, tree

stumps or holes which could cause you

to trip or stumble.

When working at heights:

– Always use a lift bucket

– Never work on a ladder or in a tree

– Never work on an insecure support

9930BA001 KN

9930BA002 KN

The drive motor is not

waterproof. To reduce

the risk of a short circuit

or electrocution, never

work with the power tool

in the rain or in wet or

very damp locations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl HSE 52 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info