Bedienungsanleitung Stihl STIHL MS 201 (Seite 15 von 132) (Englisch, Spanisch)

537128

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

MS 201, MS 201 C

English

– must, in their original condition,

meet a 45° computer derived

kickback angle when equipped with

certain cutting attachments,

– and must be equipped with at least

two devices to reduce the risk of

kickback injury, such as a chain

brake, low kickback chain, reduced

kickback bar, etc.

b) Saws with a displacement of

3.8 cubic inches (62 cm³) and

above

– must be equipped with at least one

device designed to reduce the risk

of kickback injury, such as a chain

brake, low kickback chain, reduced

kickback bar, etc.

The computer derived angles for saws

below 3.8 cubic inches (62 cm³)

displacement are measured by applying

a computer program to test results from

a kickback test machine.

In addition, features designed to reduce

kickback injuries may lose some of their

effectiveness when they are no longer in

their original condition, especially if they

have been improperly maintained.

Compliance with § 5.11 of ANSI

B 175.1-2000 does not automatically

mean that in a real life kickback the bar

and chain will rotate at most 45°.

– bar and chain combinations listed

as complying in the "Specifications"

section of the instruction manual or

– other replacement bar and chain

combinations marked in

accordance with the standard for

use on the powerhead or

– replacement chain designated "low

kickback saw chain."

See the section on "Low kickback saw

chain and reduced kickback bars."

Devices for Reducing the Risk of

Kickback Injury

STIHL recommends the use of the

STIHL Quickstop chain brake on your

powerhead with green labeled reduced

kickback bars and low kickback chains.

STIHL Quickstop Chain Brake

STIHL has developed a chain stopping

system designed to reduce the risk of

injury in certain kickback situations. It is

called a Quickstop chain brake.

All STIHL chain saws are equipped with

a Quickstop chain brake which can be

activated by inertia. If the forces of an

occurring kickback are sufficiently high,

the hand guard is accelerated towards

the bar nose even without hand contact.

See the chapter entitled "Chain Brake"

of your instruction manual.

Warning!

The computer derived angles of § 5.11

of ANSI B 175.1-2000 may bear no rela-

tionship to actual kickback bar rotation

angles that may occur in real life cutting

situations.

Warning!

In order for powerheads below 3.8 cubic

inches (62 cm³) displacement to comply

with the computed kickback angle

requirements of § 5.11 of ANSI

B 175.1-2000 use only the following cut-

ting attachments:

Warning!

To reduce the risk of injury, never use a

saw if the chain brake does not function

properly. Take the saw to your local

STIHL servicing dealer. Do not use the

saw until the problem has been rectified.

Warning!

Never operate your chain saw without a

front hand guard. In a kickback situation

this guard helps protect your left hand

and other parts of your body. In addition,

removal of the hand guard on a saw

equipped with a Quickstop chain brake

will deactivate the chain brake.

001BA174 KN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stihl STIHL MS 201 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stihl STIHL MS 201

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info