Bedienungsanleitung Stomer SCD-500 (Seite 8 von 88) (Alle Sprachen)

555252

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

OPERATION

Starting Operation

● Observe correct mains voltage! The voltage of the

power source must agree with the voltage speci-

ﬁ ed on the nameplate of the machine. Power tools

marked with 230 V can also be operated with

220 V.

Reversing the Rotational Direction

The rotational direction switch 8 is used to reverse the

rotational direction of the machine.

However, this is not possible with the On/Off switch 7

actuated.

Right rotation: For driving in screws, push the rotational

direction switch 8 left to the stop.

Left rotation: Push the rotational direction switch 8 right

to the stop (for unscrewing screws).

Switching On and Off

To start the machine, press the On/Off switch 7 and

keep it depressed.

To lock the pressed On/Off switch 7, press the lock-on

button 6.

To switch off the machine, release the On/Off switch

7 or when it is locked with the lock-on button 6, brieﬂ y

press the On/Off switch 7 and then release it.

Adjusting the Speed

The speed of the switched on power tool can be vari-

ably adjusted, depending on how far the On/Off switch

7 is pressed.

Light pressure on the On/Off switch 7 results in a low

rotational speed. Further pressure on the switch results

in an increase in speed.

Adjusting the Screw-in Depth (see ﬁ gure B)

With the adjustment sleeve 3, the screw-in depth of the

screw head into the workpiece can be preset in 8 lock-

ing steps per full turn. Each step corresponds with a

0.25 mm change of the screw-in depth.

Turning the adjustment sleeve 3 in clockwise direction

results in a greater screw-in depth; turning in anticlock-

wise direction reduces the screwin depth.

The required setting is best determined by testing.

WORKING ADVICE

● Apply the power tool to the screw only when it is

switched off. Rotating tool inserts can slip off. Guide

the screw toward the screwdriving bit 1.

The screw is held in place by the magnet pull of the

universal bit holder 9. Firmly push the tip of the screw

into the material to be screwed until the screwing-depth

stop 4 faces against the workpiece.

Switch the machine on. The screw is screwed into the

material until the adjusted screw-in depth is reached.

The drive is disengaged and the tool holder no longer

rotates. Check the screw-in depth and readjust, if re-

quired.

For unscrewing screws, set the rotational direction

switch 8 to left rotation and pull off the screwing-depth

stop 4 toward the front without turning the adjustment

sleeve. Working with the screwing-depth stop 4 is also

possible when adapting the screw-in depth.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s opera-

tion. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁ ed repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

MACHINE-SPECIFIC SAFETY WARNINGS

● Hold the machine with a ﬁ rm grip. High reaction

torque can brieﬂ y occur while driving in and loosen-

ing screws.

● Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure

than by hand.

● Always wait until the machine has come to a com-

plete stop before placing it down. The tool insert can

jam and lead to loss of control over the power tool.

● Never use the machine with a damaged cable. Do

not touch the damaged cable and pull the mains

plug when the cable is damaged while working.

Damaged cables increase the risk of an electric

shock.

FUNCTIONAL DESCRIPTION

Read all safety warnings and all instructions. Failure

to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

While reading the operating instructions, unfold the

graphics page for the machine and leave it open.

INTENDED USE

The machine is intended for driving in and loosening

screws.

ASSEMBLY

Changing the Tool (see ﬁ gure A)

Pull off the screwing-depth stop 4 toward the front. Pull

out the screwdriver bit 1. If required, the universal bit

holder 9 can also be pulled off and replaced.

After changing the tool, reattach the screwingdepth

stop 4.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SCD-500 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info