Bedienungsanleitung Stomer SMS-1500 (Seite 12 von 100) (Alle Sprachen)

555291

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

90° cross-cuts and 90° rotary table 1 14 15

• Unlock the rotary table by slackening two lock screws

(10). Set the rotary table into 90° position. Re-tighten

two lock screws (10) to ﬁ x the rotary table (8) in this

position. If the rotary table is not ﬁ xed properly, this can

result in serious personal injuries during operation.

• Place the workpiece ﬂ at on the rotary table with one

edge securely against the fence (7). If the board is

warped, place the convex side against the fence and

clamp. If the concave edge of a board is placed against

the fence, the board could collapse on the blade at the

end of the cut, jamming the blade (Fig. 14-15).

• Press On/Off switch (3) and wait for the blade (5) to

reach its maximum speed.

• Press the release button (1) and lower the machine

head by its handle (2) smoothly and with slight pres-

sure down through the workpiece to make the cut.

• When the cut is completed, return the machine to its

top parking position and let go of the On/Off switch.

Caution! A return spring causes the machine head to

rise automatically at the end of the cut. Do not let go

of the handle (2) as soon as the cut is completed but

steady the machine head and allow it to rise slowly.

90° cross-cuts and 90-45° rotary table

• Unlock the rotary table by slackening two lock screws

(10). Turn the rotary table to required angle. Re-tighten

two lock screws (10) to ﬁ x the rotary table (8) in this

position. If the rotary table is not ﬁ xed properly, this can

result in serious personal injuries during operation.

• Then follow instructions from the previous section.

90-45° bevel cuts and 90° rotary table

2 12

• Unlock the rotary table by slackening two lock screws

(10). Set the rotary table into 90° position. Re-tighten

two lock screws (10) to ﬁ x the rotary table (8) in this

position. If the rotary table is not ﬁ xed properly, this can

result in serious personal injuries during operation.

• Slacken saw blade bevel lock knob (13) and move the

saw head to the left to desired bevel angle. Tighten the

bevel lock knob (13).

• Then follow instructions on cutting from the section

“90° cross-cuts and 90° rotary table”.

• It is recommended to make a test cut in the scrap wood

ﬁ rst.

90-45° bevel cuts and 90-45° rotary table 13

• Unlock the rotary table by slackening two lock screws

(10). Turn the rotary table to required angle. Re-tighten

two lock screws (10) to ﬁ x the rotary table (8) in this

position. If the rotary table is not ﬁ xed properly, this can

result in serious personal injuries during operation.

• Slacken saw blade bevel lock knob (13) and move the

saw head to the left to desired bevel angle. Tighten the

bevel lock knob (13).

• Then follow instructions on cutting from the section

“90° cross-cuts and 90° rotary table”.

• It is recommended to make a test cut in the scrap

wood ﬁ rst. Adjustments of miter and bevel settings

are interdependent with one another. Each time you

adjust the miter setting you change the effect of the

bevel setting. Also, each time you adjust the bevel set-

ting you change the effect of the miter setting. It may

take several settings to obtain the desired cut. The ﬁ rst

angle setting should be checked after setting the sec-

ond angle, since adjusting the second angle affects the

ﬁ rst one.

Dust extraction system

When the machine is used in closed rooms, the emis-

sions of sawdust can be harmful. Beech and oak dusts

are especially detrimental to health and therefore may be

worked only with dust collector.

Always use supplementary dust extraction where pos-

sible.

MAINTENANCE

Always remove the plug from the mains socket

before making any adjustments or mainte-

nance, including changing the blade.

• Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots

free from dust and dirt. If the dirt does not come off

use a soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

• The machine requires no additional lubrication.

• Repairs should only be carried out by qualiﬁ ed persons

using original spare parts, otherwise this may result in

considerable danger to the user. Take your machine to

the SBM Group service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SMS-1500 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info