Bedienungsanleitung Stomer SRF-40 (Seite 7 von 28) (Deutsch, Englisch, Französisch)

555302

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

When the battery symbol appears for the ﬁ rst time on

the display, at least 100 measurements are still possi-

ble. When the battery symbol ﬂ ashes, the batteries/ re-

chargeable batteries must be replaced; measurements

are no longer possible.

Always replace all batteries/rechargeable batteries at

the same time. Do not use different brands or types of

batteries/rechargeable batteries together.

• Remove the batteries/rechargeable batteries from

the measuring tool when not using it for longer peri-

ods. When storing for longer periods, the batteries/

rechargeable batteries can corrode and discharge

themselves.

OPERATION

INITIAL OPERATION

• Do not leave the switched on measuring tool unat-

tended and switch the measuring tool off after use.

Other persons could be blinded by the laser beam.

• Protect the measuring tool against moisture and di-

rect sun light.

• Do not subject the measuring tool to extreme tem-

peratures or variations in temperature. As an exam-

ple, do not leave it in vehicles for longer periods.

In case of large variations in temperature, allow the

measuring tool to adjust to the ambient temperature

before putting it into operation. In case of extreme

temperatures or variations in temperature, the ac-

curacy of the measuring tool can be impaired.

• Avoid heavy impact to or falling down of the measur-

ing tool.

SWITCHING ON AND OFF

To switch on the measuring tool, brieﬂ y press the On/

Off button 1. When switching on the measuring tool,

the laser beam is not switched on yet.

To switch off the measuring tool, press the On/Off but-

ton 3 for a few seconds.

If none of the measuring tool buttons are pressed for

approx. 5 minutes, the measuring tool switches off

automatically in order to extend the service life of the

battery.

MEASURING PROCEDURE

After switching on, the measuring tool is in the length

measurement mode.

After switching on, the rear edge of the measuring tool

is preset as the reference level for the measurement.

Upon selection of the measuring function and the refer-

ence level, all further steps are carried out by pushing

the measuring button 1.

With the reference level selected, place the measuring

tool against the desired measuring line (e.g. a wall).

Push the measuring button 1 to switch on the laser

beam.

• Do not point the laser beam at persons or animals

and do not look into the laser beam yourself, not

even from a large distance.

Digital Laser Rangeﬁ nder

INTENDED USE

The measuring tool is intended for measuring distanc-

es, lengths, heights, clearances, and for the calculation

of areas and volumes. The measuring tool is suitable

for measuring indoors and outdoors.

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 On/Off and memory delete button

2 Button for selection of the reference level

6 Length measurement button

7 Display

16 Laser beam outlet

17 Reception lens

SAFETY NOTES

Working safely with the measuring tool is pos-

sible only when the operating and safety infor-

mation are read completely and the instruc-

tions contained therein are strictly followed.

Never make warning labels on the measuring tool un-

recognisable. SAVE THESE INSTRUCTIONS.

• Caution – The use of other operating or adjusting

equipment or the application of other processing

methods than those mentioned here, can lead to

dangerous radiation exposure.

• Do not direct the laser beam at persons or animals

and do not stare into the laser beam yourself. This

measuring tool produces laser class 2 laser radia-

tion according to IEC 60825-1. This can lead to per-

sons being blinded.

• Have the measuring tool repaired only through qual-

iﬁ ed specialists using original spare parts. This en-

sures that the safety of the measuring tool is main-

tained.

• Do not allow children to use the laser measuring tool

without supervision. They could unintentionally blind

other persons or themselves.

• Do not operate the measuring tool in explosive en-

vironments, such as in the presence of ﬂ ammable

liquids, gases or dusts. Sparks can be created in the

measuring tool which may ignite the dust or fumes.

ASSEMBLY

INSERTING/REPLACING THE BATTERY

Using alkali-manganese or rechargeable batteries is

recommended for operation of the measuring tool.

Less measurements are possible when using 1.2 V re-

chargeable batteries than with 1.5 V batteries.

To open the battery lid, press the latch in the direc-

tion of the arrow and remove the battery lid. Insert the

batteries/rechargeable batteries. When inserting, pay

attention to the correct polarity according to the repre-

sentation on the inside of the battery compartment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SRF-40 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info