Bedienungsanleitung Stomer SRS-220 (Seite 4 von 40) (Alle Sprachen)

555270

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Random orbit sander

INTENDED USE

This tool is intended for dry sanding and polishing of

wood, plastic, metal, ﬁ ller and painted surfaces

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 On/Off switch

2 Dust bag

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear away from the tool

• When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with

a capacity of 16Amps (U.K. 13Amps)

• In case of electrical or mechanical malfunction, imme-

diately switch off the tool and disconnect the plug

• SBM Group can assure ﬂ awless functioning of the tool

only when original accessories are used

• This tool should not be used by people under the age

of 16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use tool when cord is damaged; have it replaced

by a qualiﬁ ed person

• Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbestos is

considered carcinogenic)

• When sanding metal, sparks are generated; do not use

dustbox and keep other persons and combustible material

from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-ﬁ tting

clothes and hair protection (for long hair)

• Take protective measures when during work dust can

develop that is harmful to one’s health, combustible or ex-

plosive (some dusts are considered carcinogenic); wear a

dust mask and work with dust/chip extraction when con-

nectable

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of the

plug

• If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

• the dust suction requires the use of perforated sanding

sheets

• perforation in sanding sheet should correspond with

perforation in sanding foot

• replace worn sanding sheets in time

• always use the tool with the total sanding surface

covered with sanding paper

• before the sanding surface reaches the workpiece, you

should switch on the tool

• before switching off the tool, you should lift it from the

workpiece

• do not apply too much pressure on the tool; let the

sanding surface do the work for you

Your machine is double insulated in accord-

ance with EN 50144; therefore no earthwire is

required.

MAINTENANCE

Make sure that the machine is not live when car-

rying out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation slots free

from dust and dirt.If the dirt does not come off use a soft

cloth moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc. These sol-

vents may damage the plastic parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please con-

tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during

transport, it is delivered in a sturdy packaging. Most of the

packaging materials can be recycled. Take these materi-

als to the appropriate recycling locations. Take your un-

wanted machines to your local SBM Group dealer. Here

they will be disposed of in an environmentally safe way.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stomer SRS-220 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info