Bedienungsanleitung Storage Options 53882 - DIY Home CCTV Kit Plus (Seite 44 von 48) (Englisch)

597138

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

TROUBLESHOOTING

If a solution to your problem is not listed below, please call our technical support team (see below).

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

 System is not receiving power, or

is not powering up.

 Cable from power adapter is loose or

unplugged.

 Confirm that all cables are connected correctly.

 Confirm that the power adapter is securely connected to the

back of the unit.

 Cables are connected but system is not

receiving sufficient power.

 Confirm the system is powered on (LED indicators on front

panel should be on)

 If the DVR is connected through a power bar or surge protector,

try bypassing it and connecting power directly from the mains

socket to the DVR.

 Confirm that there is power at the outlet.

 Remote control is not detected by

the system.

 Batteries in the remote control are

drained.

 Install 2x fresh AAA 1.5V alkaline batteries in the remote

control. Ensure correct orientation.

 There are no batteries in the remote

control.

 Hard Disk Drive (HDD) is not

detected by the system.

 HDD cables are loose or not connected

properly.

 Remove the housing and check that the cables are firmly

connected.

 There is no HDD in the system.

 Open the housing and install a 3.5” SATA HDD (up to 2TB).

 HDD is full and the unit is no

longer recording

 Overwrite mode is not enabled.

 Check configuration in Main Menu  System  General.

 Mouse not detected by the

system.

 Mouse cable not firmly connected to

the system.

 Firmly connect the mouse cable to the USB port on the rear

panel of the DVR.

 Mouse is not connected to the system.

 System needs to be reset.

 Power off the system (disconnect power cable). Firmly connect

a USB mouse to the USB port on the rear panel of the DVR.

Reconnect the power cable to the DC 12V port.

 There is no picture on selected

channels / camera picture is not

being displayed.

 Camera cables are loose or have been

disconnected.

 Check the camera video cable and connections.

 Disconnect and reconnect the cable at both the system and

camera ends.

 Reconnect the camera to another channel or use another cable.

 There is no sound from attached

cameras.

 Audio cables are loose or have been

disconnected.

 Check the audio connections to the DVR.

 Audio channels are disabled in the

system menu.

 Check configuration in Main Menu  System  Encode.

 Volume on external speakers (not

included) is low / muted / off.

 Increase volume on external speakers (not included).

 A “whirring” noise is coming from

the system.

 Fan is active.

 This is normal – the exhaust fan is working.

 The system beeps at start up.

 This is normal.

 The system beeps during motion

detection.

 Motion detection is enabled and the

alarm buzzer is activated.

 Check configuration in Main Menu  Alarm  Alarm Input.

WARRANTY AND TECHNICAL SUPPORT

Support:

www.storageoptions.com/support/

Warranty:

www.storageoptions.com/warranty/

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Storage Options 53882 - DIY Home CCTV Kit Plus Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info