Bedienungsanleitung Stovax Futura (Seite 28 von 36) (Englisch)

813432

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

LEGAL REQUIREMENTS

Before installation and/or use of this appliance please read these

instructions carefully to ensure that all requirements are fully

understood.

The appliance must be fitted by a registered installer, or

approved by your local building control officer.

It is very important to understand the requirements of the

national Building Regulations and standards, along with any local

regulations and working practices that may apply. Should any

conflict occur between these instructions and these regulations

then the regulations must apply.

Your local Building Control Office can advise regarding the

requirements of the regulations.

Works must be carried out with care to meet the requirements of

Health and Safety and comply with the Health and Safety rules,

and any new regulations introduced during the lifetime of these

instructions. Particular attention should be drawn to:

— Handling: The appliance is heavy. Adequate facilities

must be available for loading, unloading and on site

handling.

— Fire Cement: Some fire cement is caustic and must not

come into contact with the skin. Protective gloves must

be worn. Wash hands thoroughly with plenty of water

after

contact with skin.

— Asbestos: This appliance contains no asbestos. If there

is the possibility of disturbing any asbestos in the course

of installation seek specialist guidance and use

appropriate equipment.

— Metal Parts: Take care when installing or servicing the

stove to avoid personal injury.

A faulty installation can cause danger to the inhabitants and

structure of the building.

For users of this appliance:

Your building insurance company may require you to inform them

that a new heating appliance has been installed on your property.

Check that your cover is still valid after installing the appliance.

FLUE OR CHIMNEY

The flue or chimney system must be in good condition.

It must be inspected by a competent person and passed for use

with the appliance before installation.

Products of combustion entering the room can cause serious

health risks.

The following must be checked:

— The construction of the masonry chimneys, flue block

chimneys and connecting flue pipe system must meet the

requirements of the Building Regulations.

— A flexible flue liner system can be used if certified for

use with solid fuel systems and installation complies with

manufacturer’s instructions and Building Regulations.

The flue liner must be replaced when an appliance is

replaced, unless proven to be recently installed and in

good condition.

— If it is necessary to fit a register plate it must conform to

the Building Regulations.

— The minimum height of the flue or chimney must be 4.5m

from the hearth to the top of the flue, with no horizontal

sections and a maximum of 4 bends. Bends must have

angles of less than 45 degrees from the vertical.

— There should be at least 600mm of vertical flue pipe

above the appliance before any bends are introduced.

— Ensure the connecting flue pipe is kept a suitable

distance from any combustible material and does not

form part of the supporting structure of the building.

— The installer must ensure the flue pipe diameter is not

less than the diameter of the outlet of the appliance and

does not narrow to less than the size of the outlet at any

point in the system.

— Make provision to remove the appliance without the need

to dismantle the chimney.

— Any existing flue must be confirmed as suitable

for the new intended use as defined in the Building

Regulations.

— The flue or chimney systems must be inspected and

swept to confirm the system is structurally sound and

free from obstructions.

— If the chimney is believed to have previously served an

open fire it must be swept a second time within a month

of regular use after installation to clear any soot falls that

may have occurred due to difference in combustion

levels.

— The flue exit from the building must comply with local

building control rules.

— Chimney heights and/or separations may need to

be increased in particular cases where wind exposure,

surrounding tall buildings, high trees or high ground could

have adverse effects on flue draught.

— Do not connect or share the flue or chimney system with

another heating appliance.

Do not connect to systems containing large voids or spaces over

230mm square.

Suitable access must be provided to enable the collection and

removal of debris.

The flue must be swept and inspected when the appliance is

installed.

FLUE DRAUGHT

The flue draught must be checked with all windows and doors

closed and any extraction fans in this, or adjoining rooms, running

at maximum speed (see Installation Checklist for ventilation

requirements).

TWIN WALL FLUE SYSTEM

If this appliance is to be used in conjunction with a twin

wall flue system then Stovax recommend the use of their

Professional XQ range. Details of this product are available

from your Stovax retailer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax Futura Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stovax Futura

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info