Bedienungsanleitung Stovax Riva Studio Bench Glass and Steel (Seite 3 von 12) (Englisch)

813434

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

SITE REQUIREMENTS

1. GENERAL REQUIREMENTS

Before installation and/or use of this appliance please read

these instructions fully and carefully to ensure that you have

fully understood their requirements.

It is important to remember the full instruction manual

supplied with this appliance deals with the installation of a

cassette insert. Using this supplement and the appliance to

create a Bench Standing changes the installation requirements

to that of a freestanding stove. As a result there are several

changes to the site requirements that must be adhered to when

locating the product.

The following section gives advice on clearances to

combustible materials in order to ensure a safe installation

The appliance must be fitted by a registered installer* or approved

by your local building control officer.

Works must be carried out with care to meet the requirements

of Health and Safety‡ and comply with the Health and Safety

rules**, and any new regulations introduced during the lifetime of

these instructions. Particular attention should be drawn to:

—Handling: The appliance is heavy. Adequate facilities

must be available for loading, unloading and on site

handling.

—Fire Cement: Some fire cement is caustic and must not

come into contact with the skin. Protective gloves

must be worn. Wash hands thoroughly with plenty of

water after contact with skin.

—Asbestos: This appliance contains no asbestos. If there

is the possibility of disturbing any asbestos in the

course of installation seek specialist guidance and use

appropriate equipment.

—Metal Parts: Take care when installing or servicing the

stove to avoid personal injury.

A faulty installation can cause danger to the inhabitants and

structure of the building.

For users of this appliance:

Your building insurance company may require you to inform them

that a new heating appliance has been installed on your property.

Check that your cover is still valid after installing the appliance.

2. MINIMUM DIMENSIONS - HEARTH

IMPORTANT: THIS APPLIANCE MUST BE FITTED TO A

BENCH BEFORE LOCATING ON A HEARTH.

PR9310

The perimeter of the hearth should be

clearly marked if flush with flooring

Model

Dimensions

A B

Studio 1 & 2 150mm 225mm

Studio 3 150mm 225mm

2.1 When installed on a Stovax bench, the bench may

stand on a 12mm thick non-combustible hearth and it is

recommended that the 225mm hearth depth should be

increased to safely contain any falling logs or embers.

2.2 The building must have a suitable load-bearing capacity for

the hearth and appliance. Consult a structural engineer for

advice before proceeding.

2.3 When fitting into an existing hearth check that the

appliance complies with current construction regulations

and is at least the minimum sizes shown.

2.4 If there is no existing fireplace or chimney it is possible to

construct a suitable non-combustible housing and hearth

setting. The flue must be installed in accordance with all

local and national regulations and current rules in force.

Check if adding a new chimney to your property requires

planning permission.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax Riva Studio Bench Glass and Steel Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info