Bedienungsanleitung Stovax Riva Vision - Wood Freestanding Stove (Seite 20 von 40) (Englisch)

813456

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Installation Instructions

† England and Wales – Document J / Scotland -

Part F/Document J (Republic of Ireland only)

‡ the latest edition of BS 8303, BS EN 15287,

BS 7566

1. Installing the Appliance

Each installation is unique to the property so it is not possible

to give details to suit every setting. The installation must comply

with Building Regulations† and be made using "best practice"

construction methods‡.

Many fireplace openings have a supporting lintel. Do not remove

without supporting the remaining structure of the building. Do not

support the structure with the appliance or the flue system.

1.1 Take care when installing the appliance. Careless

handling and use of tools can damage the finish and/or

area.

1.2 If the appliance is to be installed with an optional decorative

plinth, it needs to be fitted prior to installation, see Section 4.

Smoke Control Kit

This appliance is supplied with a pre-tted smoke

control kit and has been independently tested to

PD6434 making it exempt from the controls that

generally apply in Smoke Control Areas.

THE SMOKE CONTROL KIT IS SUPPLIED

DISABLED AND MUST THEREFORE BE MODIFIED

BEFORE INSTALLATION IN ORDER FOR THE

APPLIANCE TO MEET THE REQUIREMENTS OF A

SMOKE CONTROL AREA AND MUST BE OPERATED

CORRECTLY TO MINIMISE THE AMOUNT OF

SMOKE PRODUCED.

This appliance is suitable for use in a Smoke

Control Area when burning wood and following the

instructions for use specied in this manual but

ONLY if the Smoke Control kit has been enabled.

If this appliance is installed outside of a Smoke

Control Area then the Smoke Control kit can be

disabled to give more control over the lower burn

rates.

Any modifications to the kit should only be done by

a suitably qualified installer and MUST be done at

the time of installation, see Installation Section 6.

1.3 Select and fit the required flue option.

1.4 The Riva Vision must be secured to the hearth using

the fixing points provided. Failure to do so may result in

damage to the appliance.

If mechanical fixing is not possible Stovax recommend

the use of a back stop or semi-fixing the appliance using

silicone sealant applied to the inside edges of the base.

1.5 Position the appliance where required on the hearth and mark

the location of the fixing holes in the mounting bracket.

1.6 Drill the required sized holes into the hearth.

1.7 Use suitable fasteners to fix in place.

Fixing holes in

hearth mount

2. Top Flue Installation

2.1 The appliance is factory supplied with a top flue outlet but

the flue collar and blanking plate require sealing with Fire

Cement before use, see Diagram 2.

Flue Collar

Decorative

Flue Ring Fire Cement

sealed all around

Fire

Cement

sealed all

around

Blanking

Plate

Flue Collar Inner

2.2 To fit the pipe to the collar:

— Lift appliance into position.

Take care not to damage the hearth finish.

— If a glass top is to be fitted this must be done prior to

connecting the flue, see Section 5.

— Connect appliance to the chimney using flue pipe.

— Seal the connecting joints.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax Riva Vision - Wood Freestanding Stove Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info