Bedienungsanleitung Stovax Studio (Seite 7 von 48) (Englisch, Französisch, Italienisch)

813436

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

GENERAL INFORMATION

Installing the Appliance

Each installation is unique to the property so it is not possible to give

details to suit every setting.

The installation must comply with Building Regulations and be made

using "best practice" construction methods.

Take care when installing the appliance. Careless handling and

use of tools can damage the finish and/or area.

Appliance Location

Many replace openings have a supporting lintel. Do not remove

without supporting the remaining structure of the building. Do not

support the structure with the appliance or the ue system.

If installing with a Dedicated External Air Kit, please consult manual

PM361 prior to installation

Registered Professional:

Before installation and/or use of this appliance please read these

instructions fully and carefully to ensure that you have fully understood

their requirements.

The appliance must be fitted by a registered installer, or approved by

your local building control officer.

Structural Support:

If installing on a wooden floor check that the floor joists are strong

enough to bear the weight of the insert, chimney and construction parts.

Hearth:

A Constructional Hearth with a depth of 125mm and a 12mm.

Decorative Hearth Plate must be installed to protect a combustible floor

from the risk of falling embers if mounted directly on the floor.

The Decorative Hearth must extend 300mm in front of the hearth and

can be made of natural stone, concrete, metal or glass.

If this appliance is installed on a Stovax Bench, the bench may stand

on a 12mm thick non-combustible hearth and it is recommended that

the 225mm hearth depth should be increased to safely contain any

falling logs or embers.

Do not store combustible material under the bench.

Final inspection of the installation:

When it has been installed, the appliance must be commissioned in

accordance with standards and practices to ensure full working order

and a correct handover given to the customer.

Flue and Chimney

The flue or chimney system must be able to withstanding flue

temperatures of up to 4000C.

The external diameter of the connection sleeve is 155mm.

In normal operating mode, draft in the chimney should be 20-25 Pa

close to the connection sleeve. The draft is affected primarily by the

length and area of the chimney and also by how well sealed it is.

The minimum recommended chimney length is 3.5m and a suitable

cross-section area is 150-200cm² (140-160 mm in diameter).

Sharp bends and horizontal lengths in a flue pipe reduce the draft in the

chimney.

It must be possible to sweep the full length of the flue, and the soot

doors must be easily accessible.

Carefully check that the chimney is sealed and that there is no leakage

of smoke from the connections.

Combustion Air Supply

When the appliance is installed, it is essential to ensure adequate air

is supplied to the room. Air can be provided indirectly via a vent in the

outer wall or via a duct from the outside that connects to the sleeve on

the underside of the insert. The required volume of combustion air is

about 20 m3/hour.

The outer diameter of the combustion air connection sleeve is 80mm.

If a pipe is longer than 1 m, its diameter must be increased to 100mm

and a larger wall vent will be required.

In heated spaces, the flue must be insulated to prevent condensation

using 30mm mineral wool covered with a vapour barrier. The hole in the

wall (or floor) at the exit point must be properly sealed with flue jointing

compound.

A flexible pipe to provide external directly into the appliance is available

and must be fitted at the time of installation.

CO Alarms

Building regulations require that whenever a new or replacement fixed

solid fuel or wood/biomass appliance is installed in a dwelling a carbon

monoxide alarm, complying with BS EN50291, must be fitted in the

same room as the appliance.

HETAS recommend the unit is permanently fixed in accordance with the

manufacturer's installation instructions or with the guidance contained in

Approved Document J where no other information is available.

Provision of an alarm must not be considered a substitute for either

installing the appliance correctly or ensuring regular servicing and

maintenance of the appliance and chimney system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stovax Studio Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stovax Studio

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info