813428

Stovax View 7 Inset High Output Boiler Inset Seite 12

12
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
12
8.4 Place the ash into a Stovax Ash Caddy (Stovax Part No.
4227) or other suitable container.
8.5 Check and remove ash as often as required when burning
solid fuel.
8.6 De- ash at least once a week.
8.7 Do not place hot ash in a container made from plastic or any
other combustible material.
9. Over-Firing
9.1 Do not over-fill with fuel or run at high temperatures for long
periods or over-firing can occur.
DO NOT OPERATE THE APPLIANCE WITH THE
PRIMARY AIR CONTROL OPEN FOR LONG PERIODS
OF TIME AS THIS COULD CAUSE OVER-FIRING AND
MAY CAUSE PERMANENT DAMAGE.
9.2 Over-firing can cause permanent damage to the
appliance and invalid the product warranty.
10. Chimney Fire
10.1 If a chimney fire occurs:
— Shut all air controls immediately.
— Evacuate the building.
— Call the fire brigade.
— Do not re-enter the building until it is confirmed safe.
10.2 Do not use the appliance after a chimney fire until:
a) It has been inspected by a registered installer*,
confirming the appliance is safe to use.
b) The chimney system has been inspected and swept by a
chimney sweep, confirming the system is structurally sound
and free from obstruction*.
c) It is repaired as required before re-use. Use only
genuine Stovax replacement parts to keep your appliance in
safe, efficient working order.
11. General Cleaning
11.1 Clean and inspect the appliance regularly, especially in
periods of heavy use. Regular cleaning and maintenance
will help give many years of safe use.
11.2 Allow appliance to cool thoroughly to avoid risk of
burns.
11.3 Clean regularly, according to level of use.
Remove the ash completely.
(See User Instructions, Section 8).
10.4 Check the internal components for damage and for obvious
build up of soot, ash or debris above the flue baffle(s) (these
can be found in the upper part of the firebox). Use a torch if
necessary.
11.5 If there are any signs of a build up of debris above the flue
baffle(s) either:
— Arrange for the chimney to be swept (see Care &
Maintenance Instructions, Section 13).
— Remove the baffles and clear the debris
(see Pre-Installation Instructions, Section 5).
11.6 Clean matt black appliances using Stovax Colloidal black or
Stovax Grate Polish.
11.7 To refresh painted finishes a touch up spray is available.
Contact your Stovax retailer quoting the serial number found
on the appliance date badge.
Do not use aerosol sprays near an operating appliance.
Do not use abrasive cleaner or cleaning pads.
Check that the door shuts properly and creates an effective
seal. Leaking door seals prevent the appliance working
properly.
12. Cleaning Glass
12.1 Keep the glass clean with correct use of the Airwash system
and good quality fuel. Use the boost setting to clear any
build up.
12.2 Sometimes additional cleaning may be required.
Before undertaking this operation allow appliance to cool
fully. Do not clean hot glass.
12.3 On appliances with printed glass do not use cleaning
agents that have a high alkaline or acidic content, for
example Stovax Gel Cleaner, these are aggressive
cleaning agents designed to be used with heavily
stained clear glass. On printed glass surfaces, use
Stovax Glass Cleaner (Stovax No.4103) which is better
formulated for this application.
12.4 Before applying a cleaning agent remove any dust and
loose soot with a damp cloth.
12.5 Use an appropriate glass cleaner. Apply the cleaning fluid to
a cloth before rubbing onto the glass.
Apply carefully and do not apply excessively. Try to prevent
any run off which could soak into the rope seals around the
edge of the glass.
Soot can also contain acidic particles that can cause
corrosive damage to printed glass.
12.6 Remove dirt with a moist cloth and buff dry.
12.7 Some types of wood and solid fuel can cause a white
residue to form on the glass.
If this occurs it should be cleaned off at least once a
week during periods of heavy usage.
If the liquid cleaning agents recommended do not
remove this residue use a dry cleaning pad which will
help remove these white marks.
12.8 Before relighting the appliance ensure the glass is fully dried.
If the rope seal has absorbed excess cleaning agent it
is advisable to replace the rope as soon as possible to
preserve the printed finish of the glass.
Care & Maintenance
*Registered on the Competent Persons Scheme (GB
only) see page 38/ INFO (Republic of Ireland).
… 12 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stovax View 7 Inset High Output Boiler Inset wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info