Bedienungsanleitung Stromer Pedelec 2017 (Seite 22 von 37) (Englisch)

780325

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

22 23

Read the operating instructions for the char-

ger before beginning to charge the battery.

You can change the battery of your Stromer while

it is installed in your Pedelec. However, you can

also remove the battery from the Pedelec and

charge it in another place. It is particularly ad-

vantageous to charge it in a warmer environment

(room temperature) when it is cold outside, in or-

der to shorten the charging period. Avoid charg-

ing processes below 0 °C or above 40 °C and in

tightly sealed spaces. The charging process is au-

tomatically stopped at temperatures below 0 °C

or above 40 °C.

Please note that a sudden change of tempera-

ture from cold to warm can cause condensation

to build up in the charger. Avoid this by storing

the battery in the same place where it is charged.

Only use the charger supplied or a charger re-

leased by Stromer to avoid the risk of ﬁre.

Use the charger in a dry room and don’t cover it up

while it is in use. It could otherwise short circuit

or cause a ﬁre.

Check the mains voltage before connecting the

charger! The voltage of the power source must

correspond to the information on the type plate

of the charger.

• Always pull the plug out of the socket before

cleaning the charger.

• The charger should be disconnected from the

mains once the charging process has been

completed.

For safety reasons, always place the charger

on a dry, non-ﬂammable surface.

A defective battery should neither be

charged nor used any further. A battery can be-

come warm while charging. It must not get hot.

When the battery heats up strongly, immediately

terminate the charging process.

Never ride when the battery is not inserted.

The battery compartment can in this case not be

locked. This poses an additional risk of falls and

injuries.

Charging the battery

Always read the charger information ﬁrst.

Charging the battery externally, outside

the Pedelec

First connect the charger to the mains pug (LEDs

light up red and green) and then to the battery.

Hold the charging cable loosely in your hands and

bring it gradually closer to the socket of the battery.

The magnets will help you to position the plug

correctly.

The LEDs in the charger light up in orange and

green during the charging process.

The LEDs in the charger light up in green when

the battery has been fully charged. Separate the

battery/Stromer from the Stromer charger and

then the charger from the mains connector.

Charging the battery internally in the

Pedelec

The connection for the charging cable is located

on the left side of the down tube, slightly below

the connection to the head tube.

Open the cover of the charging socket.

1. Connect the charger to the power mains. The

integrated LEDs light up in red and green.

2. Hold the charging cable loosely in your hands

and slowly move it near the socket of your

Stromer. The magnets will help you to posi-

tion the plug correctly.

3. Connect the Stromer charger with the Stromer.

The LEDs light up in orange and green.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stromer Pedelec 2017 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stromer Pedelec 2017

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info