Bedienungsanleitung Stromer ST2 - 2020 (Seite 19 von 44) (Englisch)

780318

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ANTI-LOCK BRAKING

SYSTEM WITH A PINLIFT ON

THE REAR AXLE

myStromer cannot be held liable for dam-

age caused by unreasonable, unpredictable and/

or inappropriate use of the anti-lock braking sys-

tem (ABS).

• Use of the S-Pedelec should always be adjusted

to the overall situation, including trafﬁc pat-

terns and your riding skills.

• In addition, the anti-lock braking system (ABS)

actively inﬂuences the braking function of your

S-Pedelec. Please bear in mind that, in certain

situations, your braking distance may actually

be extended.

The capacities of your anti-lock braking

system (ABS) have limits!

• In extreme riding conditions, such as hard brak-

ing on a slippery surface, setting off on steep as-

cents or when panicking, your might not be able

to steer your S-Pedelec as you expected. When-

ever possible, always try to avoid late and hard

braking because you were relying too much on

your anti-lock braking system (ABS).

As an additional optional safety measure, your

S-Pedelec may also have an anti-lock braking

system (ABS) on the front axle with a pinlift on

the rear axle. This set-up allows for controlled

braking on slippery surfaces and should prevent

you from falling over the bicycle in the event of a

hard brake. The anti-lock braking system is fully

integrated into your S-Pedelec and may only be

differentiated using the ABS control light on your

OMNI display.

Before you ﬁrst use the anti-lock braking system

(ABS), it is essential that you carefully read the

operating manual from the manufacturer, Blu-

brake, which you can ﬁnd at www.stromerbike.

com/support and on their own website.

Before the ride:

The anti-lock braking system must be initialized

before each use. You can do this by carefully acti-

vating the front wheel brake at a speed of at least

5km/h after the S-Pedelec has been turned on/

woken up/unlocked. The orange ABS control light

on the OMNI display should no longer light up af-

ter this process. Do not start your ride until you

have successfully initialized the system.

During the ride:

If the ABS control light is displayed during the

ride, this means there is a problem or malfunction

of the system. Restart your S-Pedelec and perform

the initialization again.

If the control light still does not turn off,

consult a specialist Stromer bicycle retailer imme-

diately.

As long as the brakes have no mechanical de-

fects, the S-Pedelec can still brake without the

anti-lock braking system (ABS).

Maintenance and warranty

General work on the braking system must only

ever be performed by a specialist Stromer bicycle

retailer. If the maintenance is not performed in

accordance with the speciﬁcations and/or if work

is performed by unauthorized personnel, the war-

ranty and/or guarantee of the whole anti-lock

braking system is immediately voided.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stromer ST2 - 2020 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Stromer ST2 - 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info