Bedienungsanleitung Strong SRT 40FX4003 (Seite 17 von 23) (Englisch)

751402

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Satellite Select the satellite for this TV.

LNB Type Make sure the LNB type is corresponding to your dish.

LNB Power: Set the power supply for the LNB (usually 13/18 V).

22KHz Select the 22KHz to set 22K switch to ON/OFF. The Auto mode (recommended) is

used to switch 22KHz on or off depending on the LNB type.

DISEqC1.0/1.1 Select the DiSEqC mode for the selected LNB.

Highlight Satellite and press ENTER to access the satellite list and select one. Highlight LNB Type and

press ENTER to select the LNB type. Make sure the 22KHz, DISEqC1.0/1.1 switch is corresponding to the

selected satellite. After the above steps are finished, press the BLUE button to search for channels.

5.4.3 DTV Manual Tuning (in DVB-T/C mode only)

Search and store programmes manually.

Select the source type DVB-T or DVB-C and search digital programmes manually. In the Channel menu,

select DTV Manual Tuning and press ENTER to access. Press t u to select a Channel No., and then press

ENTER to start the search. The search stops when a programme is found and this programme will be

stored in the current channel position. If you want to stop the search, press MENU.

5.4.4 ATV Manual Tuning (in DVB-T/C mode only)

First select the source type of ATV. Then in the Channel menu, select ATV Manual Tuning and press

ENTER to access. Highlight and press p q to select Storage To 1 (maybe other number), Sound System

and Channel No.. Then select search and press ENTER to start the search. Press u for the unit to search

towards higher frequency. Press t for the unit to search towards lower frequency. The search stops

when a programme is found and this programme will be stored in the current channel position. If you

want to stop the search, press MENU.

Fine-Tune

Use this option to make small adjustments to tuning of an individual channel. Fine-tune is not

necessary under normal conditions. However, in area of inferior broadcast conditions where adjustments

is necessary for a better picture and sound, use fine-tune. Select a channel that you want to fine tune. In

the Channel menu, select ATV Manual Tuning and press q to highlight Fine-Tune. Press t u to fine tune

until the best possible picture and sound are obtained.

5.4.5 Channel settings

Programme Edit Edit the programmes. You can press the COLOUR BUTTONS on the remote

control to skip programmes, rename and delete programmes or move

programmes, and add programmes to the favourite list by pressing FAV.

Signal Information Showing the information of current DTV channel.

Cl information Enables the user to select from the CAM-provided menu. Select the Cl menu

based on the menu PC card.

5 V Antenna Power This option is only available in DVB-T source, select On to supply power for

the TV’s antenna. Select Off to turn off this function.

Software Update (OAD) Select On to allow the TV to update the system software over the air. Select

Off will turn off this function.*

OAD Tuning When software update (OAD) is off, this option is disabled. By selecting OAD

scan you can scan channels to find the OAD update information.*

*Only for some regions.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 40FX4003 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 40FX4003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info