Bedienungsanleitung Strong srt 4356 pvr (Seite 14 von 74) (Deutsch, Englisch, Italienisch)

424428

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Part 1 • English

www.strongsat.com 25

z Dish Position: Select "Dish position" and press OK or the Right button. It

displays the dish position of the current satellite. When you use a DiSEqC 1.2

positioner, you can select dish position in this field. To set a dish position, the

status must be "On" (in case the position has already been set) or "Off" (in

case the position has not been set).

NOTE: If in the "LNB Set-up" menu described in section 5.1.4.2, the "LNB Dish"

item is set to "fixed" you will not be able to change the dish position settings in the

channel set up menu. Only when you have selected the "LNB Dish" to "moved",

you will be able to change the settings in the channel set up menu.

z Press OK button to set dish position. The "Positioner Set-up" menu will be

displayed. (Detailed description is in Positioner Set-up section 5.1.4.3.1)

z Frequency, Polarization, Symbol Rate:

(Please see inside cover Screen

17)

Shows the transponder (TP) values of the current satellite. To change the value

apply the following steps:

1. Select "Frequency" and press OK. The list of TP values of the current satellite

is displayed.

2. The functions of the coloured buttons are switched to represent other

functions.

3. To edit a TP value, press the Red (Edit) button.

4. To change the current TP value, press the Blue (Add) button

5. Press the Green (Save) button to save the settings.

6. Press the Yellow (Delete) button to delete the current TP value. (Save is only

available in tile Edit mode or the Add mode.)

z Scan Mode: Designate channels scanning whether "FTA" (Free to Air) only or

"All" channels (including scrambled channels).

z Network Search: Set this field to "On" to perform Network TP Search.

z AutoScan (Red Button): This function searches all the transponders of a

satellite.

(Please see inside cover Screen 19)

z Net. Scan (Blue Button):"Network Search" Performs network search for a

transponder.

z TP Scan (Green Button):Search channels from current specific transponder.

Part 1 • English

26 www.strongsat.com

z PID (Yellow Button): You can search a specific channel by entering the PID

value of a channel, If you press the Yellow (PID) button, the PID screen is

displayed. Enter the PID value and press the Yellow button again. To cancel

the PID value, press Exit on the remote control or press the Yellow (PID)

button to search the channel. You should enter V-PID, A-PID and P-P1D as

described in "Editing channels from the channel list" (Described in section

5.1.1).

Tip: Check the level and quality of the signal bar before searching any channels. The

signal level of the TP of the current satellite is displayed. The green bar is displayed if

the settings are correct, otherwise the red bar is displayed and you cannot get the

channel. In the latter case, check if your dish is aimed at the selected satellite or if the

DiSEqC switch of the LNB overlaps with another satellite. Also, change the Frequency

with the Left/Right button until the Green bar is displayed to get the valid transponder.

If you press the Red (Auto Scan), Blue (Net. Scan), Green (TP Scan), or Yellow (PID)

button the channel searching status is displayed.

5.1.4.3.1 Positioner Set-up (if you are using a Motorized positioner with

DiSEqC1.2). (Please see inside cover Screen 20)

If you are using a motorized positioner with DiSEqC 1.2 you will have to set the

positions of the satellites you want to scan. This function is available only if in the "LNB

Set-up" menu and the LNB Dish field is set to "Moved". (As described in "LNB Set-up"

(Described in section 5.1.4.2).

Before you start:

1. Make sure that your installer has set the center position of your dish.

2. Make sure that the mechanical limits of your motor are set, so that no damage

can be done to your dish by moving it too far to the East/West.

3. Make sure you set the highest Symbol Rate (Ksymbols/sec) for your chosen

transponder (TP). The Signal level and Quality indicator will help you set up

the best dish position possible.

4. Use your UP/DOWN buttons to select the "Dish Position" field in the "Channel

Set-up' menu.

5. Press the OK button and the "Positioner Set up" Menu will be displayed.

6. Start setting the position of the selected satellite.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong srt 4356 pvr Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info