Bedienungsanleitung Strong SRT 6500 CI (Seite 14 von 27) (Englisch)

480583

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

PART 1 • English

English

5.2.3 Channel Search

Press OK on ‘Channel Search’ in the Setup Menu. The following window will appear.

Set the Satellite, Tune Method, Transponder, Frequency, Symbol Rate, FEC and Function.

n Use CH p/q to move up and down the list.

n Use Vol t/u to change the setting.

Satellite Name: choose from the list of satellites selected in “Antenna setup” menu.

Tune Method:

Main options are:

“Sat” – receiver will search channels according to stored list of transponders.

“Sat – NIT” - receiver will search channels according to stored list of

transponders and in addition use network information. This mode allows

you to ﬁnd all channels, even from new appeared transponders.

“TP” – this method is to search channels from one transponder.

“TP – NIT” – receiver will search channels from one transponder and in

addition use network information. This mode recommended if you want

to search channels of particular broadcaster only.

Sub options are:

“Free” – receiver will search only Free To Air channels

“Free+Scr”

– receiver will search for all channels

Transponder:

select index from the stored list

Frequency:

value of transponder frequency in MHz

Symbol Rate: value of symbol rate in kSymbols Per Second

Polarity: Horizontal / Vertical / Right / Left

FEC: Auto, 1/2, 2/3, 3/4, 5/6, 7/8

Function: Append/Delete/Change

AGC Signal: Indicates received signal strength level

5.2.3.1 How to search for channels:

Highlight “Tune method” ﬁeld and press OK. Receiver will start channel scan. Names of the found channels will be shown in the two

columns: for TV and Radio separately.

You can interrupt search process by pressing to

OK or EXIT button.

If you press OK button: search process will be interrupted and you can select one of the following options:

n Save – to save all found channels

n Unselect – to unselect some unwanted channels from the list. Use OK button to unselect channels and Vol t/u buttons to switch between

TV and Radio list. Once you ﬁnish – press EXIT button, select “Save” and press OK. Only selected channels will be stored in the memory

n Cancel – to cancel result of search. No channels will be stored in the memory

If you press EXIT button: search process will be interrupted and no channels stoRED in the memory.

5.2.3.2 How to add new transponder:

n set “Tune method” to “TP” or “TP+NIT”

n move focus to “Frequency” and enter value in MHz

n move focus to “Symbol rate” and enter value in kSPS

n move focus to “Polarity” and select value

n move focus to “FEC” and select value or set “Auto”

n move focus to “Function” select “Append” and press OK. Message “Saving data...” will be shown on screen. New transponder

will be added to the end of the list

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 6500 CI Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info