Bedienungsanleitung Strong SRT 6502 (Seite 12 von 22) (Englisch)

480582

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

PART 1 • English

English

“TP – NIT” – receiver will search channels from one transponder and in addition use network information. This mode

recommended if you want to search channels of particular broadcaster only.

Sub options are:

“Free” – receiver will search only Free To Air channels

“Free+Scr” – receiver will search for all channels

Transponder: select index from the stored list

Frequency: value of transponder frequency in MHz

Symbol Rate: value of symbol rate in kSymbols Per Second

Polarity: Horizontal / Vertical / Right / Left

FEC: Auto, 1/2, 2/3, 3/4, 5/6, 7/8

Function: Append/Delete/Change

AGC Signal: Indicates received signal strength level

8.2.3.1 How to search for channels:

Highlight “Tune method” ﬁeld and press OK. Receiver will start channel scan. Names of the found channels will be shown in the two

columns: for TV and Radio separately.

You can interrupt search process by pressing to OK or Exit button.

If you press OK button: search process will be interrupted and you can select one of the following options:

n Save – to save all found channels

n Unselect – to unselect some unwanted channels from the list. Use OK button to unselect channels

and VOL t/u buttons to switch between TV and Radio list. Once you ﬁnish – press EXIT button,

select “Save” and press OK. Only selected channels will be stored in the memory

n Cancel – to cancel result of search. No channels will be stored in the memory

If you press EXIT button: search process will be interrupted and no channels stored in the memory.

8.2.3.2 How to add new transponder:

n set “Tune method” to “TP” or “TP+NIT”

n move focus to “Frequency” and enter value in MHz

n move focus to “Symbol rate” and enter value in kSPS

n move focus to “Polarity” and select value

n move focus to “FEC” and select value or set “Auto”

n move focus to “Function” select “Append” and press OK. Message “Saving data...” will

be shown on screen. New transponder will be added to the end of the list

8.2.3.3 How to delete present transponder:

n set “Tune method” to “TP” or “TP+NIT”

n move focus to “Transponder” and choose transponder you want to delete

n move focus to “Function” select “Delete” and press OK. Message “Saving data...”

will be shown on screen. Selected transponder deleted from the list

8.2.3.4 How to correct/edit parameters of the transponder:

n set “Tune method” to “TP” or “TP+NIT”

n move focus to “Transponder” and choose transponder you want to modify

n move focus to “Frequency” and enter value in MHz

n move focus to “Symbol rate” and enter value in kSPS

n move focus to “Polarity” and select value

n move focus to “FEC” and select value or set “Auto”

n move focus to “Function” select “Change” and press OK. Message “Saving data...”

will be shown on screen. Modiﬁed data are stored in the memory.

n Press EXIT to go back to the previous mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 6502 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info