Bedienungsanleitung Strong SRT 7300 CI plus (Seite 9 von 23) (Englisch)

568532

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PART 1 • English

4.0 STARTING UP FOR THE FIRST TIME

Ensure that your satellite signal is of good quality and that all connections are sound. In case of

difﬁculties or questions, please ask you local dealer for assistance. It is recommended to follow the Setup

Wizard step by step. It will guide you through the basic installation and channel searching process. You

can enjoy digital HD broadcasts within just a few minutes.

4.1 Language selection

After turning on the power for the ﬁrst time, the language selection menu will appear. Choose your language

with pq and conﬁrm with OK. A welcome screen will now be displayed. Once you are ready, press OK to

start the wizard. During any stage of the Setup Wizard, you can press EXIT to get back to the previous screen.

4.2 System Setup

Here you can set the Country, Aspect Ratio, Conversion Mode and Subtitle Language. Use pq to move

the highlight and tu to change settings. To see a list of all possible settings for the highlighted option,

press OK. Once all settings are made, move the highlight to NEXT and press OK to continue.

4.3 Satellite Selection

Use pq to highlight the satellite your dish is aimed at and press OK to conﬁrm.

If your dish is aimed at Astra 1C, 1E, 1F, select ASTRA 19.2E. The SCAN MODE screen will appear.

If your dish is aimed at HOT BIRD, select HOTBIRD 13E.The SCAN MODE screen will appear.

If your dish is aimed at another satellite, select OTHER. You will be guided to the Satellite Settings menu.

Refer to chapter 7.1.1 for instructions.

Note: If Germany or Austria is chosen as country and ASTRA 19.2E as satellite,

German and Austrian pre-installed channels are available. An extra screen

will then be displayed giving a choice between Preinstalled & Scan and Satellite

Scanning. Choose Preinstalled & Scan to install the German or Austrian pre-

installed channels and continue with the Setup Wizard as described from point

4.4 or choose Satellite Scanning to continue without pre-installed channels.

4.4 Scan Mode

Use pq to highlight the desired option and press OK to conﬁrm.

All: Will scan all available channels on the chosen satellite.

Free: Will scan FTA (Free-To-Air) channels only.

4.5 Signal Adjust

This screen allows you to ﬁne tune the alignment of your dish antenna for optimum reception.

Use tu to select the switch input the dish is connected to. (If the LNB of your dish is directly connected

to the receiver, choose Switch Input 1) The bars on the bottom of the screen indicate the current signal

strength and quality. A red bar indicates a bad signal. Green bars indicate a good signal. Yellow bars

indicate that the signal condition is nearly acceptable.

Adjust your dish for maximum possible signal quality and strength. Once the signal cannot be improved

anymore, ﬁx the dish on this position and press OK to continue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7300 CI plus Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 7300 CI plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info