Bedienungsanleitung Strong SRT 7806 (Seite 13 von 30) (Englisch)

751654

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

4.2.2 Dish Setting

Satellite Get information about your satellite setting. It cannot be changed.

LNB Power Select On to supply powering for selected LNB or Off to switch it off.

LNB Type Select Universal for most standard LNBs or SatCR if you have a SatCR LNB or

multiswitch. You can set another LNB type, using User defined parameter.

LNB Freq (Low/High)

The LOF (Local Oscillator Frequency) of the LNB is usually printed on the LNB itself or

in its documentation. You can set the High and Low LOF frequencies to match the LNB

here.

22KHz Tone The receiver uses 0 or 22 kHz signal to control the band of the LNB.

DiSEqC1.0 Get information about the selected satellite LNB.

Tone Burst Get information about the provided tone burst control for satellite switch.

Transponder This option allows you to set the transponder which is used as a reference for the

satellite signal strength.

Signal Strength and Signal Quality bars

In two level bar meters, on the bottom of the screen, you can see the strength and

quality of the signal coming from the antenna dish to the tuners. These two meters

can be used while doing a fine-tuning of the antenna position. The antenna has to be

adjusted to maximum possible signal strength and signal quality.

4.3 Channel Search

In order to view video programmes, you must do a channel search with or without smartcard in order to

install the channel list of your choice.

For HD+ channels, first insert HD+ smartcard at the right-hand side of the receiver before you start the

channel search. Then the receiver will install the associated channel list of the HD+ bouquet (FTA and

encrypted).

For FTA only channels or for channels from other satellites you do not need to insert a HD+ smartcard.

Select the search scheme you wish the wizard to follow:

1. Select HD+ channels to search for channels of the HD+ bouquet (channels 100 and above).

2. Select Preinstalled channels to restore a predefined German channel list from the receiver’s

memory (channels 1~99).

3. Select Advanced channel search to search for channels on all transponders for the selected

satellite (channels above the HD+ bouquet).

Finding and storing the channels

Select preferred option or press the GREEN button on the remote control to start the channel search.

Once a channel search has started, a progress bar and list of channels will be displayed. At any time, you

may stop the search by pressing on the remote control. After the channel search is completed, the

receiver will save all found channels into the channel list and exit to the preview mode.

NOTE: If you see the messages No list found or No channels found, please check the antenna

connections and signal levels of the satellite dish.

5.0 QUICK GUIDE FOR USING YOUR RECEIVER

We at STRONG understand that you can’t wait to enjoy your new HD+ receiver.

However, we advise you to read this manual to get the best performance from your STRONG HD+

receiver. To turn your receiver ON or to go to Standby mode, press q on the remote control. Choose

channels with CH+/ or p q. Alternatively, you can also enter the channel number with the 0~9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7806 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 7806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info