Bedienungsanleitung Strong srt 8345 (Seite 18 von 31) (Englisch)

424993

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

PART 1 • English

English

To add channel press YELLOW (Save) or BLUE (Save&Exit) button. The new channel will be added to the

list with name “Video CH XXXX”, where XXXX is equal to PCR PID (Video) you have entered.

5.2.1.1 Positioner setup

If in Dish setup menu you have conﬁgured Dish mode as “DiSEqC 1.2” then you have to setup position

of the dish to each satellite that you want to install.

In Channel setup menu move menu focus to Dish position item and press OK button on remote control.

Menu Positioner setup will appear on screen.

n Satellite: Displays the name of satellite position of antenna for which you setup

n Transponder: Use tu buttons to select reference transponder, receivable in your location, to

measure signal strength and quality

n Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to

ﬁne adjust position of the dish (each press to direction button will turn dish

to short angle). Fast speed can be used to adjust dish position roughly. If

Movement speed set to Fast press to direction button will couse continuous

movement of the dish to appropriated direction, to stop dish you will have to

press OK button.

n Move: Use tu buttons to move dish to the East/West direction

n Centre position: If you press OK button while menu focus is on this item then dish will be

turned to centre position, which corresponds to true South direction.

n Limits: Use tu buttons to Enable or Disable software limits of your positioner.

n Set limit: Use tu buttons to select East or West limit of dish movement range.

Step by step recommendations of position setup.

n Select reference transponder in order to check signal strength and quality during position setup.

n If you do not know current direction of your dish then move menu focus to Centre position

item and press OK. Dish will be turned to true South. Knowing your location longitude you

may understand direction where necessary to move dish in order to reach position of selected

satellite. For example: your longitude is 5° East and you want to setup dish position for Astra 1C,

1E (19° East). Then, from centre position, you need to move dish to East direction by pressing to

t button. If your longitude is 25° East then, in order to setup dish position for Astra 1C, 1E (19°

East), you need to move dish in West direction (from centre position) by pressing to u button.

n To setup roughly position of the dish set Movement speed to Fast. Then move menu focus

to Move item of the menu and by short presses to t or u buttons move dish to necessary

direction. Check signal strength and quality indicators. Once levels start increasing – press OK

button to stop the dish. Set Movement speed to Slow and keep adjusting dish position until get

best possible values.

n Once you are sure that dish is ﬁne adjusted press YELLOW (Store) or BLUE (Store & Exit) button.

Dish position for selected satellite will be stored.

NOTE: in order to avoid mechanical damage of your dish please, make sure those mechanical

limits in your motor are set correctly and dish would not hit any objects on its movement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong srt 8345 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong srt 8345

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info