Bedienungsanleitung Strong SRT 8502 (Seite 9 von 21) (Englisch)

480561

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Українська

Antenna Power: Use the tu to turn antenna power on / oﬀ/. Before connecting the

antenna, please read the User Guide for the antenna. If you use an active

internal or external antenna that requires power supply voltage of 5 V DC

and consumes less than 50 mA, then set it to On. Otherwise, set it to Oﬀ.

After all settings are made (including the adjustment of the antenna), press BLUE button on the remote

control to start scanning for channels.

The receiverwill start searching forchannels. On the screenwill be displayed information about the

scannedfrequency,foundTV and Radiochannels andchannel searchprogress. Once thechannel scanis

complete, the receiverwill turnon the ﬁrst channel, whichis in the list.

NOTE: If at the end of the search the receiver did not found channels, it is

possible that your antenna is not correctly installed/aligned. To ensure

good results and the proper antenna conﬁguration, refer to qualiﬁed

professionals.

4.1 Activation ofthe receiver inthe digital terrestrialTV operator‘s network

IMPORTANT Your receiver comes pre-activated to view most of the encoded

digital terrestrial channels broadcast by the operator on a free basis

to subscribers. However, watching some channels may require fee. To

gain access to paid channels, you should contact Customer Support.

Information required to contact the Customer Support are in the

additional instructions that came with the documentation supplied

with the receiver.

After the ﬁrst turn the receiver will automatically receive additional

information from the digital broadcasts. The process of obtaining the

data may take several minutes, during which the receiver will display a

message that there is no right to watch a channel. At this time, do not

change channels. Wait for the image of the transmitted channel.

5.0 DAILY OPERATIONS

In this section of the manual sets out the most frequently used functions the receiver.

5.1 Switching on and oﬀ the receiver

To switch your receiver ON and OFF, use the button marked with q. This button is located on the remote

control and front panel of the receiver.

Press on this button to switch the receiver into standby mode that consumes no more than 1.00 watts of

power. Press the button again to turn receiver to operating mode.

If you plan not to use the receiver for a long time, unplug it from the mains by unplugging the power

adaptor from the outlet.

5.2 Changing channels

5.2.1 Switch channels in the view mode

For the sequential switching of channels in the view mode you can use buttons pq or PG+ / PG. For

direct switching to a channel with a certain number you can dial the channel number using buttons 09.

5.2.2 Switch channels through the channel list

To switch between the channels through the channel list, do the following:

 In view mode, press OK - on the TV screen will be displayed a list of channels.

 Using the button pq select from the list a channel you are interested to watch and press OK -

channel list will disappear from the screen and the receiver will show the chosen channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8502 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info