Bedienungsanleitung Strong SRT 8525 (Seite 16 von 27) (Englisch)

480560

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

PART 2 • English

English

6.3.1 Language Setting

In this menu you can set your language of chioce for menu, audio and subtitles.

OSD Language: Use t/u to select menu language.

Audio Language: Digital TV allows transmitting more than one audio track/

language. If a channel has multiple audio tracks/languages,

the receiver will select the suitable audio track/language

automatically according to your selection.

Subtitle Language: This setting allows you to deﬁne the subtitle language. Use t/u

to select a subtitle language and the receiver will display the

subtitles in this language automatically (if available). If you do not

want to display subtitles, then adjust the setting to Oﬀ.

NOTE: Subtitles will be displayed when available. Availability depends on the

local broadcast.

Please also consider that events may contain “built in” subtitles which can’t be disabled.

6.3.2 Output Setting

In this menu you can set the output parameters of the receiver according to the connected TV set

and for the connected audio ampliﬁer if applicable.

TV Mode: Use t/u to select the mode. Commonly the PAL standard is

used, but it might be that you need to use the setting NTSC. We

recommend referring to the user manual of your TV set to check

the correct setting.

Video Output: Use t/u to select between RGB and CVBS modes.

Screen Mode: Use t/u to adjust this setting in accordance with the aspect

ratio of your TV set (4:3 or 16:9) and the preferred conversion.

The options are: Auto (automatic detection of aspect ratio), 4:3

Panscan (displays 16:9 broadcasts full screen and cut upper and

lower parts of 16:9 video on your 4:3 TV), 4:3 letterbox (displays

16:9 widescreen broadcasts with black bars on top and under the

picture on a 4:3 TV). For a modern 16:9 TV set following options

can be set: 16:9 Wide Screen, 16:9 PillarBox (4:3 broadcasts will be

shown with black vertical bars on the left and right side of the

image) and 16:9 Pan&Scan. We recommend trying these settings

in order to ﬁnd the option that suits you best. Do not forget

about the possibility to control the TV format via the menu of

your TV set.

HDMI Output: Allows you to change the resolution of the HDMI output. If the

connected TV does not support the set resolution you will see a

black screen. In this case, wait for 10-15 seconds without pressing

any buttons on the remote control of the receiver, and the

previous value will be recovered automatically.

Loop out in stand-by: This allows to by-pass the antenna signal to the ANT OUT

connector, where you may have an additional TV set/receiver

connected, in order to receive analogue/digital broadcasts there

too.

Digital audio: Use t/u to adjust this setting in accordance to the used audio

equipment. To loop the digital audio through HDMI or S/PDIF to

a connected ampliﬁer, home theatre or other equipment able to

decode AAC and AC3, set RAW HDMI ON.

If neither your TV set nor any other connected audio equipment support decoding AAC and AC3,

adjust RAW HDMI OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8525 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info