Bedienungsanleitung Strong SRT 8903 (Seite 11 von 27) (Englisch)

480558

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

PART 2 • English

3.7 Connecting a USB storage device

Note: We recommend the use of a hard disk drive USB 2.0 or higher for recording

and play back of TV events.

For proper functioning of Timeshift and recording functions, a fast USB device (such as a hard

disk drive) is needed. Interrupted playback or distorted pictures during playback or Timeshift are

indications for a low device speed. STRONG cannot guarantee proper functioning of recoding and or

Timeshift functions with all USB devices.

4.0 STARTING UP FOR THE FIRST TIME

If you have a Conax smartcard from your provider, please insert it into the CA slot on the right hand

side of the receiver, behind the ﬂap. Insert the card with the chip side down.

If you use your receiver for the ﬁrst time, the Welcome “Easy install” menu appears. Use pq to move

the highlight to the setting you wish to alter and use tu to change values. Start by selecting your

region using tu. Once you have selected your region, press q to move the highlight to Language.

Select your language using tu.

Language Select your language.

Region: Select your region where this receiver is used.

Subtitle: Select Normal to display subtitles per default, Select Hard of Hearing to show

HoH subtitles per default. Select Off to hide subtitles per default.

Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred

conversion method. Options are: Auto (automatic detection of aspect ratio),

4:3 Panscan (Displays 16:9 widescreen broadcasts full screen on your 4:3 TV),

4:3 letterbox (black bars on top and under the picture on a 4:3 TV) and 16:9

(use this setting for 16:9 TV sets).

Scan mode: Select All to store scrambled and free to air channels or select Free to store

only free to air channels.

Connection: Use this option to select the connection to your TV set. Select HDMI or TV

SCART. If you are using a cinch cable then this selection is not important.

Once all settings are made, move the highlight to OK and press OK to continue.

Note: Wrong region selection can lead to missing channels or channels being

stored on wrong positions in the channel list.

The receiver will now advance to the Aerial Adjustment screen.

This part of the wizard is of great help when setting up your antenna system.

Use pq to move the highlight to the setting you wish to alter and use tu to change values. The

following settings are available:

Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will be present on

the ANT IN connector of the receiver. Select Off for passive antennas.

Beeper: Select On for an audible indication of signal reception. Off turns the beeper off.

Channel No.: Select a channel that is known to carry a broadcast in your region. The Signal

Strength and Signal Quality bars give a visual indication of the reception.

Adjust your antenna to obtain maximum signal strength and quality.

Once all settings are made, press OK to start scanning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 8903 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info