Bedienungsanleitung Strong SRT6020 (Seite 17 von 26) (Englisch)

65945

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

PART 1 • English

English

n Update from SD card

First you need to store the ﬁle with extension *.crd to the root folder of the SD card. File with software

update can be downloaded from our web site www.strongsat.com. Insert the SD card with *.crd ﬁle to

the SD card slot of the receiver. Go to menu System Setting – System Update. Select SD Card Data and

press OK. On the left side of the screen you will see the list of folders, at the right side you will see the list

of ﬁles in root folder. Use UP/DOWN buttons to select ﬁle with software update and press OK. Conﬁrm

the update. The message “Updating software from SD card. Please wait” will appear on screen. Receiver

will reboot automatically once the update is ﬁnished.

NOTE: Do not eject SD card during software update process.

n Update through PC to STB

Connect the computer to the receiver (receiver must be powered off) with a 9-pin cross cable (two

females). The computer will follow the steps below:

Start->Programs->Accessories->Communications->Hyper terminal

Then choose “COM1” or “COM2” according to the computer port you are using and port setting

as follows:

Bits per Second: 115200

Data bits: 8

Parity: None

Stop bits: 1

Flow Control: None

In Hyper Terminal menu select “Transfer”

item and then press “Send ﬁle” item. Select the ﬁle with

the new software (*.UPD) you want to download and choose the protocol “1K Xmodem”. Finally

press OK and a download menu will appear in the computer screen. Power on the receiver, then the

download process will begin. After about 2.5 minutes, the message “OK, Reset” will appear on the

computer on Hyper Terminal window, which means the download has been completed successfully.

Power off the receiver and then unplug the RS-232 interface.

*NOTE: INCORRECT OPERATION MAY CAUSE UNREPAIRABLE DAMAGE TO THE RECEIVER.

1. DO NOT POWER OFF THE RECEIVER DURING THE PROCESS OF DOWNLOAD.

2. DO NOT PLUG IN OR UNPLUG THE RS-232 INTERFACE WHEN RECEIVER IS

POWERED ON

5.4 Timer

You can set the timer to make the receiver perform designated actions including timer based wake

up or sleep instructions to the receiver. Use the

UP/DOWN buttons to select timer. Press the RED

key to activate/inactivate current timer. Press the

OK button to enter your selected timer settings.

Action: You can select the following functions:

“Power On” The receiver powers on at the designated date and time within deﬁned channel.

“Time interval”

The receiver switches on at the designated date and time, displays the channel and

then switches off at the designated date and time (The value set at the end time).

“Power Off” The receiver powers off at the designated date and time.

Cycle: You can set the cycle of the action designated in the timer mode (One time, Daily or Weekly).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT6020 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT6020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info