Bedienungsanleitung Sub-Zero UC15 (Seite 5 von 44) (Englisch, Französisch, Spanisch)

651825

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

subzero.com

CUBE WEIGHT

Cube weight increases or decreases depending on the

amount of dimple, or depression in the octagonal-shaped

ice cube. Cube weight can be adjusted by increasing the

freeze time.

To adjust cube weight:

1 Touch and hold ‘POWER’.

2 Touch and release ‘CLEAN’ once to add one minute of

freeze time. Inspect the cubes after several production

cycles and repeat if a heavier cube is desired. Up to ve

minutes of additional freeze time can be added.

3 Touch ‘CLEAN’ six times to reset freeze time to the

factory setting.

ICE LEVEL

A thermostat in the ice storage bin signals ice production to

stop when the bin is full. If ice production stops before the

bin is full or continues after the bin is full, the ice level can

be adjusted. The thermostat control is located behind the

kickplate. Refer to the illustration below.

To adjust ice level:

1 Remove the kickplate to access the thermostat control.

2 Turn the control to the left to decrease the level of ice or

to the right to increase the level.

Operation

PRIOR TO USE

Clean the ice machine thoroughly with warm water and mild

detergent. Rinse and dry with a soft cloth to remove any

residual oil and grease left from the manufacturing process.

Refer to care recommendations on page 6.

All surfaces that come in contact with the water system

should be cleaned and sanitized prior to use. Refer to the

cleaning and sanitizing procedure on page 7. Use only the

cleaner and sanitizer made for the Sub-Zero ice machine.

Ice machine cleaner and sanitizer can be ordered online at

subzerowolfstore.com. For questions, contact Sub-Zero

customer care at 800-222-7820.

ICE PRODUCTION CYCLE

Depending on ambient conditions and water temperature,

one ice production cycle takes approximately 30 minutes.

1 Water ll cycle. The water inlet valve purges old water

from the system.

2 Refrigeration system start-up. The compressor starts

after the water ll cycle and remains on throughout the

freeze and harvest cycles. The condenser fan motor

starts and runs throughout the freeze cycle.

3 Freeze cycle. Water is sprayed into the inverted cups.

The water freezes layer by layer until an ice cube forms

in each cup. The control system adjusts the length of the

freeze cycle to conditions.

4 Harvest cycle. The evaporator warms, allowing the

cubes to be released and drop into the storage bin. The

control system adjusts the length of the harvest cycle

to conditions. At the end of the harvest cycle, another

freeze cycle begins.

5 Automatic shut-off. The level of ice in the storage bin

controls the automatic shut-off. When the bin is full, ice

will contact the bin thermostat, which cools, signaling ice

production to stop. When the ice level drops and ice no

longer contacts the bin thermostat, it will warm, signaling

ice production to resume.

OPERATION

THERMOSTAT

CONTROL

Ice level adjustment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sub-Zero UC15 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info