Bedienungsanleitung Sunrise Medical Argon (Seite 11 von 100) (Englisch, Holländisch, Französisch)

514909

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ARGON 11

ENGLISH

0505/2/ST-000690645.EMS 1B

ENGLISH

Footplate Adjustment

Divided and Platform

Footplates

(Fig. 6.4 - 6.6)

Footplates can be flipped up to

facilitate getting in and getting

out of your wheelchair.

They can also be tilted to six

different angles relative to a

level surface. Tighten screw (1)

firmly on the outer side.

By removing the clips (2), the

footplate can be adjusted to

three different positions toward

both the front and rear.

Loosen the adjustment screw

(3) to change the horizontal

position of the footplate. For

this purpose, the footplate must

be flipped up. When finished,

make sure that all screws have

been properly tightened (see

the page on torque). A minimum

interval of 2.5 centimeters from

the ground should always be

maintained.

Adjusting the Footrest (Fig.6.7)

Removing screw (1) will allow

you to adjust the footrest to

correspond to the length of

your lower leg. The angle of

the footrest may be indi vi d ual ly

adjusted (not rigid foot rest) by

loosening nuts (2). The footrest

bracket (3) prevents feet from

un inten tion ally slipping out place.

When finished, make sure that

all screws have been properly

tightened (see the page on

torque).

Castors, Castor Plates, Forks

From time to time the wheelchair may veer slightly to the right

or left, or the castors may flutter. This may be caused by the fol-

low ing:

Forward and/or reverse wheel motion has not been set •

properly.

The castor angle has not been adjusted properly.•

Castor and/or rear wheel air pressure is incorrect; wheels •

do not turn smoothly.

The wheelchair will not move in a straight line if the castors

have not been properly ad justed. Castors should always be

adjusted by an authorized dealer. The castor plates must be

readjusted, and the wheel locks must be checked any time the

rear wheel posi tion has been altered.

Castor

Seat

Castor

Adjusting the castor (Fig.6.9 - 6.10)

To ensure that both forks are set parallel,

simply count the teeth visible on both sides.

After setting the castor fork, the teeth will

guarantee a secure position, allowing an

adjustment of 16° in 2° increments.

Use the flat side to check for a right-angled

position to the ground.

The patented design allows the castor fork

to be turned, so that it can be reset at right-

angles to the ground when the seat angle is

changed.

Adjusting the seat height

(Fig.6.8)

To adjust rear seat height, slacken

and remove the 4 Torx screws

(1) (2 each side) and the thread

washer (2), which secures the

clamp (3) for the camber tubes

to the axle plates (4). Adjust the

two camber tube clamps (3) to the

required height and replace the 4

Torx screws. Before tightening the

screws, please follow the instructions for setting the toe-in/toe-

out to zero (See Fig.6.13 - 6.15).

Tighten the screws to 7 Nm.

NOTE – An adjustment to the castor angle may be necessary

when adjusting the rear seat height.

Fig.6.4

Fig.6.5

Fig.6.6

Fig.6.7

Fig.6.8

Fig.6.9

-8°+8°

Fig.6.10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sunrise Medical Argon Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info