Bedienungsanleitung Sunrise Medical Quickie Q500 (Seite 28 von 120) (Englisch, Holländisch, Französisch)

682541

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Q500 M/F/R Rev.B

ENGLISH

Checking controller:

• Check the thin rubber gaiter or boot around the base of the

joysck sha for damage or spling. Check visually only, do

not handle the gaiter.

• Make sure that all components of the control system are

securely mounted. Do not over-ghten any securing screws.

Checking controls:

• Switch on the hand control – Do the lights ash? This

signies that there is a fault in the electronic system. Refer

to chapter 9 for basic troubleshoong

• Operate all of the electric opons, including lights and

indicators, (if ed), to make sure that they work correctly.

• With the seang in an elevated posion, drive the

wheelchair to make sure that the ‘creep’ mode works which

will slow the wheelchair.

• Drive the wheelchair in each of the drive proles to make

sure the wheelchair performs as it did before.

WARNING!

• If you are in any doubt about the performance

requirements of your wheelchair contact your Sunrise

Medical authorised dealer.

• Aer performing any maintenance or repairs on the

wheelchair you must make sure that it is funconing

correctly before it is used.

• A complete inspecon, safety check and service should be

made by a Sunrise Medical authorised dealer at least once

per year.

• All fasteners must be replaced like for like using the correct

length, tensile strength and materials.

• When replacing self-locking nuts, or nuts/studs secured

with a thread locking soluon, ensure that a suitable thread

locking soluon is reapplied to the fastener.

• Check all Velcro fastening straps for correct adhesion when

pressed together.

• Ensure that any contaminaon, such as u, hair,etc is

removed from the Velcro straps. Such contaminaon may

aect adhesion.

Monthly checks

Perform the monthly check roune before driving as described

below.

• All fasteners should be checked monthly for wear, such as

loose bolts or broken components.

• Check all straps monthly for fraying, ripped seams or other

indicaons of excessive wear damage. Disconnue use if

damage is found.

8.2 Tyre maintenance and pressures

8.2.1 Tyre pressure

CAUTION!

If pneumac tyres are ed to your wheelchair it is important

to regularly check the air pressure and for signs of wear.

The maximum tyre pressures are listed in Secon 8.3, if in

doubt check the markings on the side of the wheelchair tyre

for guidance.

NOTE: It is important that drive wheels are inated to equal

pressures as a pair, and likewise the rear. The inator pump

provides the safest method of inang your wheelchair tyres

and the pressure can be checked with a standard motor

vehicle pressure gauge.

DANGER!

• Do not inate beyond the maximum allowed tyre pressure.

• Always use the pump that is supplied with the chair,

8.2.2 Tyre wear

When inspecng the tyres for signs of wear, look for signicant

scu marks, cuts and a diminished tyre tread. Tyres will

need to be changed when the tread cannot be seen over the

complete surface of the tyre, (Fig.8.1).

Fig. 8.1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sunrise Medical Quickie Q500 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info