Bedienungsanleitung Suntec Klimatronic Heat PTC 2000 flame (Seite 15 von 110) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

767577

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

put into standby mode.

•To switch on the unit, press the on/off button on the control panel. Each operation on the control panel

is accompanied by an acoustic signal. The fan heater is activated with the following standard settings:

low heating level (1300W), target temperature 25°C, activated fireplace simulation.

•The brightness of the LED display is reduced by 1/3 during operation if no adjustment is made after one

minute. The brightness is increased again as soon as any key is pressed.

•Fireplace simulation

oTo switch the fireplace simulation on or off, press the corresponding key on the control panel.

The corresponding indicating light lights up or goes out. The fireplace simulation can be used

independently of the fan heater and also in standby mode.

•Heating level

oYou may select from two heating levels using the corresponding button on the control panel:

▪low heating level (1300W)

▪high heating level (2000W)

The corresponding indicating light lights up.

•Oscillation

oTo turn the 80° oscillation on or off, please press the corresponding button on the control

panel. The corresponding indicating light lights up or goes out.

•Timer

oUse the timer to set the time after which the unit shall switch off automatically. You may set the

time between 0 and 24 hours. If 0 hours are chosen, the timer is deactivated.

oPress the "+" or "-" keys to increase or decrease the number of hours by one hour each. If you

hold down the respective button, you can choose between the hours faster.

oOnce you have selected your desired time, please wait for five seconds. During this time the

number flashes and is then saved. The display now alternately shows the target temperature

and the remaining time in an interval of 30 seconds.

oIf you want to change the set time, press the "+" or "-" buttons again, then wait for five seconds.

oWhen the time is over, the appliance enters the standby mode.

•Thermostat

oThe thermostat allows you to set a target temperature between 15°C and 35°C. As soon as the

room temperature reaches the target temperature, the fan heater switches off and is only

switched on again when the room temperature is below the set target temperature.

oPlease use the "+" and "-" keys to increase or decrease the target temperature by one °C each.

If you hold down the respective button, you can choose between the temperatures faster.

oOnce you have selected your desired target temperature, please wait for five seconds. During

this time the number flashes and is then saved. The display now shows your target temperature.

oIf you want to change the target temperature, press the "+" or "-" buttons again, then wait for

five seconds.

oNotes:

▪In the first ten seconds of operaton, the room temperature and target temperature

cannot be compared. If the room temperature is equal to or higher than the target

temperature after the ten seconds, the fan heater and the heat level indicator lights

switch off. The fan heater switches on again as soon as the target temperature is higher

than the room temperature.

▪If the NTC within the appliance has a short circuit, the LED display shows "EE" and the

temperature cannot be set. In this case, please contact your point of sale.

▪If the room temperature is below -10°C, the LED display shows "LO". If the room

temperature is above 40°C, the LED display shows "HI". These displays serve as

indicators for the very cold or very warm room temperature.

•Eco mode

oIn Eco mode, the target temperature is set to 22°C and the heating level is automatically

adjusted according to the room temperature. To switch on or off, please press the corresponding

key on the control panel. The corresponding indicating light lights up or goes out.

oThe heating level is automatically adjusted in Eco mode as follows:

▪Room temperature under 18°C: high heating level

▪Room temperature between 18°C and 22°C: low heating level

▪Room temperature over 22°C: no heating level (fan heater is turned off)

oIn Eco mode, all settings, except for heating level and target temperature, can still be made.

•Tip-over protection

oThe unit is equipped with a tip-over protection. If the unit tips over or is tilted too far, the unit

switches off automatically. The appliance switches on again as soon as it is in an upright position

again.

•Overheating protection

oThe overheating protection switches the unit off automatically in the event of overheating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Suntec Klimatronic Heat PTC 2000 flame Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info