Bedienungsanleitung Suntec Wellness Transform 10500 (Seite 7 von 13) (Englisch)

549834

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

COOLING

 We recommend starting TRANSFORM early in the morning on warm days to get a cool room..

 This TRANSFORM unit has a self-evaporation function for condensation water, so that it is normally not

necessary to empty the water tank in cooling mode. The drainage hose need not be connected. Please

make sure that the outlet is closed with the rubber cap during operation.

(This does not apply in the case of high air humidity. If the TRANSFORM unit operates in cooling mode for a longer period and

especially at a time of year with high air humidity, the condensation tank may be full. The control lamp will remind you to empty the

water. Refer to error message E4. In such a case, empty the water tank via the condensation water outlet. If continuous high air

humidity is likely, it is recommended to drain the condensation continuously via the drainage hose.)

COOLING IN INDOOR OPERATION

The TRANSFORM unit stands in the room to be cooled.

Connect the air hose and the air outlet grid to the TRANSFORM unit as displayed in the illustration; the air

hose connection piece and air outlet grid need to be exchanged.

The warm extract air must be emitted from the room via the air hose. This can be executed e.g. via a tilted

window, a door or wall aperture. Make sure that no warm outside air can enter the room. For effective

cooling, we recommend our selection of various accessories which reduce or prevent entry of warm air into

the room.

Set the function to „COOLING“. Set the target temperature using the temperature control. The settable

temperature range is between 17°C and 30°C target temperature. The TRANSFORM unit must only be

used in an ambient temperature of maximum 32°C.

Note: After switching on, or over, the ventilator operates, but the compressor only starts after the control lamp has flashed for 3

minutes. Cooling effect may require a further 10 minutes. Further information is available under the item, „Troubleshooting“.

COOLING IN OUTDOOR OPERATION

The TRANSFORM unit is outside the room to be cooled.

Connect the air hose and the air outlet grid to the TRANSFORM unit as displayed in the illustration; the air

hose connection piece and air outlet grid need to be exchanged.

Place the TRANSFORM unit in the shade if possible and in a cool place in order to increase efficiency and

to avoid overheating. At an ambient temperature of over 32°C, the TRANSFORM unit may deactivate. If th is

occurs continuously, we recommend you temporarily use the INDOOR OPERATION of the TRANSFORM

unit. We recommend that a drainage hose for condensation water be connected.

Set the function to „COOLING“. The settable temperature range is between 17°C and 30°C. This can be se t

using the temperature control.

The air with high oxygen content cooled by the TRANSFORM unit is led into the room via the air hose. This

can be executed e.g. via a tilted window, a door or wall aperture. Make sure that no warm outside air can

enter the room. We recommend that a drainage hose for condensation water be connected. For effective

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Suntec Wellness Transform 10500 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info