Bedienungsanleitung SunTech CT40 (Seite 32 von 52) (Englisch)

704206

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 32

NOTE: If the temp probe is returned to the probe well before the “long beep” is heard, no temperature measurement will

be displayed.

NOTE: Be sure to eject the used probe cover into an approved bio-hazard container before attempting to place the probe

back in the isolation chamber.

Other FILAC® 3000 Temperature Settings

Your device’s FILAC® 3000 thermometer operates in several different modes.

Quick Mode is an oral predictive measurement mode that provides a fast reading. Quick Mode allows you to rapidly

identify patients with normal body temperatures. If the patient temperature is outside of the “normal” range, the

FILAC® 3000 electronic thermometer will automatically switch into its standard predictive mode to provide a more

accurate reading. Quick Mode is indicated by a rabbit icon on the display . Quick Mode is not available when in

Cold Mode or in Direct Mode.

The FILAC® 3000 thermometer normally operates in predictive mode to provide fast and accurate temperature

measurements. However, in instances when no measurement site is detected, or the temperature does not stabilize,

the thermometer will automatically switch to Direct Mode . Additionally, the FILAC® 3000 electronic thermometer

will automatically switch into Direct Mode if the ambient temperature is greater than 35°C (95°F). If this happens, you

will hear two short beeps and see the Direct Mode turtle icon appear . This icon will be continuously displayed

whenever the thermometer is functioning in Direct Mode. The Direct Mode auto feature is always functional for both

the Red or Blue isolation chamber/probe combinations.

Cold Mode can be selected if a patient’s body temperature is expected to be lower than normal, such as when he is

coming out of surgery. Cold Mode is activated by pressing the Site Selection button and °C/°F button simultaneously

on the temp module. When selected, the Cold Mode snowflake icon is displayed, and the probe will preheat to

33°C (91°F). The accuracy and measurement time of Cold Mode measurements are equivalent to standard prediction

measurements at the respective body sites.

Touchless Thermometry Module*

If your device comes with the optional touchless thermometry module, you can easily and quickly measure the

patient’s temperature using a touchless infrared temporal thermometer. To use, remove the thermometer from the

holster on the side of the SunTech CT40. Touch the thermometer’s START button to turn on the touchless

thermometer.

On your SunTech CT40 display, you will see the Human Thermometry Mode icon selected with the arrow pointing to

the side of the head . Hold the thermometer probe 2 cm to 3 cm from the patient’s temple and press the START

button on the back of the thermometer. The reading is complete when you hear a beep, and the temperature

measurement will appear on your device display. Place the thermometer back in the device holster.

NOTE: Be sure to wipe away any sweat from the area around the temporal artery and be sure to remove eyeglasses and

push hair away from measurement site before initiating a measurement.

NOTE: The area just behind the ear lobe can be used as an alternative measurement site to the temporal artery.

NOTE: The SunTech Touchless Thermometer should not be used near sources of heat or cold, such as a heater or air

conditioner vent. Also, do not use outdoors. Use this product in a room where the temperature is between 16°C and

40°C (61°F and 104°F).

NOTE: If patients are subject to a significant change in temperature from outside to inside, the patient should be

allowed to acclimate for approximately 15 minutes before using the touchless thermometer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SunTech CT40 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SunTech CT40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info