Bedienungsanleitung SunTech CT40 (Seite 44 von 52) (Englisch)

704206

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 44

Why is no heart rate data showing on the display?

If the device is configured to use the Sp02 sensor as the pulse rate source, and the sensor is not attached to the

patient, there will not be heart rate data on the display. Only dashes will appear, or MAP results if MAP measurement

is enabled. Note that MAP is not available in the United States.

How many measurements can be stored in the SunTech CT40 memory?

The SunTech CT40 can store 99 unique sets of measurements. After the 99th measurement has been saved, the next

measurement will have the Memory Location Identifier label “01” and will overwrite the most recent measurement

(measurement 99). After all results are cleared from the memory, the Memory Location Identifier also will return to

“01.”

14. Technical Information

EMC Statement

This equipment needs special precautions regarding EMC and needs to be installed and put into service according to

the EMC information provided in this document. This equipment has been tested and found to comply with the limits for

medical devices to IEC60601-1-2: 2014. These limits are designed to provide reasonable protection against harmful interference

in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no

guarantee that interference will not occur in a particular installation. When the device accuracy of any value displayed on the

monitor is questionable, determine the patient’s vital signs by alternative means. If it is determined that the device is

malfunctioning, stop using the device and have the device checked by a qualified service technician before further use. If this

equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving device.

Increase the separation between the equipment.

Connect the equipment into an outlet on a circuit different from which the other device(s) are connected.

Consult the manufacturer or field service technician for help.

Portable and mobile RF communications equipment can affect Medical Electrical Equipment.

WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external

antennas) should be used no closer than 30 cm (12 inches) to any part of the CT40 system, including cables

specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.

WARNING: Use of accessories, transducers, and cables other than those specified may result in increased emissions

or decreased immunity of the CT40.

WARNING: The CT40 should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is

necessary, the CT40 should be observed to verify normal operation in the configuration in which it will be used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

SunTech CT40 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von SunTech CT40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info