Bedienungsanleitung Superrollo RM10MM (Seite 22 von 68) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

650849

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Starting up the device

Before the device can be used, the following steps must be carried out:

■ Connect the motor cable to the intended junction or switch box

■ Carry out a test run

■ Mount the roller shutter curtain on the winding shaft

■ Set the upper and lower terminal stop point.

Connecting the device

Connection of the tubular motor to the mains power and all work on electrical

systems may only be carried out by a certified specialist electrician according to

the connection schematics contained in these instructions.

DANGER

Fatal electric shock due to coming into contact with live

components.

¾ Do not carry out any connection work on the device when it is

connected to the current supply.

¾ Make sure that the device is disconnected from the mains power

supply.

ATTENTION

Malfunctions or damage to the motor due to incorrect mains

voltage.

¾ Compare the information on the model plate with that of your local

mains power supply.

¾ Make sure that the device is only connected to a 230 V ~ 50 Hz

mains power supply.

ATTENTION

Short-circuit due to damaged cables.

¾ Make sure that the cable cannot be damaged by moving parts in

the roller shutter box.

ATTENTION

Short-circuit due to water in the motor on routing cables

incorrectly.

¾ Never route the cable vertically upwards.

¾ Always route the cable in a loop.

Routing the cable in a loop enables the water to drip off (1.).

¾ Connect the motor cable to the junction or switch box (2.) intended for this

purpose.

2.1.

Item No. Motor cable wire colour Function

1 Black Direction of rotation 1

2 Brown Direction of rotation 2

3 Blue Neutral conductor

4 Green/yellow Earth

Carry out a test run to check whether the motor's direction of rotation corresponds

to the switch position.

¾ Operate the motor to lower the roller shutter.

¾ Check whether the motor runs in the downwards direction.

If the motor does not run in the downwards direction, the cable assignment must

be changed.

¾ Swap the motor cable's brown wire over with the black wire.

¾ Make sure that the direction of rotation corresponds to the switch position.

In order to connect the device to a single-pin roller shutter switch,

observe the installation plan on page 28.

Installing the roller shutter curtain

The following prerequisites must be met in order to be able to install the roller

shutter curtain:

■ The roller shutter curtain must lie in the guide rail.

■ The tubular motor must be run all the way down.

ATTENTION

Damage to the tubular motor due to drilling or screwing.

¾ Never drill or screw the winding shaft in the area of the tubular

motor.

¾ Use only the holes available in the winding shaft to secure the roller

shutter curtain.

¾ 1. Approx. every 40 cm, slide a securing spring (1) onto the top slat of the roller

shutter curtain (2).

¾ 2. Insert the securing springs into the rectangular holes (3) in the winding shaft.

1. 2.

1 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Superrollo RM10MM Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info